x,400a40R,Fig. Equivalent Circuit of IMLest's consider three phase, Y connected, 220 volt(line to line), 7.5 kW, 60 Hz, six pole IM has the following parameter values in /phase referredto the statorR = 0.294 N, R= 0.144 fN, X, = 0.503 N, X, = 0.209N, Xm13.25 NDetermine the following for 0.03 slipa) Electromechanical Torque (Tmech), Electromechanical power (Pmech}.b) Maximum electromechanical torque (Tez), Corresponding speed (n mar)) Electromechanical statrting torque (Tiart), Corresponding stator load current (I, start)a. Tmech63.3705 N. m, Purch 7293.87 W, n.rar = 950.539 rpm, Tmaz153.768 N. m, Ia start= 175.257 A, Tstart = 70.2798 N.b. Tmech= 55.4105 N. m, Pech3933.77 W, n, mur = 919.728 rpm, Tmar154.791 N. m, Iz sart125.567 A. Tart72.5229 N.c. Tmech65.4105 N. m, Prch7872.83 W, n, mar825.827 rpm, T- = 154.758 N. m, 1 stare:145.657 A. Trt73.7912 N.d. Tmech = 65.4105 N.m, Prch= 7973.13 W. n, 969.827 rpm, T = 174.564 N. m, art- 150.265 A. Tytart77.6227 N.e. Tmech = 55.2537 N. m, Pmech2353.62W. nmaz = 925.793 rpm. T220.437 N. m. or115.562 A. Ttart57.7327 N.

According to question: The synchronous speed 'Ns' and motor speed 'Nr' is calculated as The value…

Lest's consider three phase, Y connected, 220 volt(line to line), 7.5 kW, 60 Hz, six pole IM has the following parameter values in 1/phase referred to the stator: R=0.294 N, R= 0.144 N, X, = 0.503 N, X, = 0,209 2, Xm = 13.25 N

Lest's consider three phase, Y connected, 220 volt(line to line), 7.5 kW, 60 Hz, six pole IM has the following parameter values in 1/phase referred to the stator: R=0.294 N, R= 0.144 N, X, = 0.503 N, X, = 0,209 2, Xm = 13.25 N

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An 8.2kW seriesd generator has an armature resistance is 0.25 ohms with a generated voltage equal to 4212.43 V. Determine the series field resistance should be installed in this machine in order to supply a load at 400V.
Fhe number of parallel paths and the number of series conductrs required for a given kW reting are determined by. System voltage Armature resistance Type of winding Field current
An electricity generation and distribution system consists of an AC generator, a step-up transformer, transmission lines and a series of step-down transformers providing AC electricity to the end users. The system has the following characteristics: The system is represented in the schematic of Figure below. Assume it is operating at maximum power output. (i) Generator power output-48.4 MW Generator voltage output - 24.2 kV rms Generator frequency - 50 Hz Transformer efficiency - 100% Step-up transformer loop ratio - 1:10 Total resistance of transmission lines-6.00 Series of step-down transformers: effective overall loop ratio - 1000:1 (iii) (iv) generator step-up transformer resistance of transmission lines 6.00 12 T step-down transformer city Determine the peak-to-peak voltage of the output of the generator. On a graph paper provided, sketch a graph of 'Voltage output (kV) versus 'Time (s)' for the generator. Show two complete cycles. Determine the rms current in the primary coil of…
OR e) Explain the following protection schemes of alternators. i) Stator inter turn protection. ii) Merz price protection.
A 3-phase, 50 Hz,2000 kVA, 2300 volt alternator gives a short circuit current of 600 A for a certain field excitation. For the same excitation, the open circuit voltage was 900 volts. The resistance between pair of terminals was 0.12 ohm. A)Ifthe generator is wye connected, -Determine the full load regulation at 0.80 lagging pf. -Determine the full load regulation at unity pf
Please solve these questions below
The zener regulator 5.6 V DC is interfaced with 6.4 V DC relay. How many voltages should be provided by the DC power supply as shown in given Figure?
EX3 Voltage Sag 400 V network short circuit power is 1000 kVA (reactive). A 10 kW induction motor is connected. The motor takes 6-times nominal current when started (assume inductive current). Calculate the voltage drop as a) per unit value, b) per cent value, c) volts in line voltage, d) volts in phase voltage.
7. The following test results of a single-phase step-down transformer which were measured at primary side: Open Circuit Test: Voc= 415V; loc= 0.22A; Poc= 7.64W; Vo=240V Short Circuit Test: Vsc= 25.2V; Isc= 18.07A; Psc= 142.43W An inductive load was then connected to the step down transformer and recorded that the full load output current Is 31.25A. Determine: a. Equivalent resistance of the transformer referred to the primary circuit Req and equivalent reactance of the transformer referred to the primary circuit Xeq, b. Transformer core loss resistance Re and inductor core loss Xm, c. Percent Voltage Regulation V.R. of the transformer when delivering full load power 5700W at power factor 0.8 lagging.
54. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the following a. Equivalent reactance b. Total impedance c. Voltage drop across the capacitor
56. A single phase thyristor adjust line spacing converter with a resistive load is shown below: V₂ = V sinest SCR ER R V₂ (B) 1.11 (D) 1.44 If the supply voltage is 230V (rms) at 50 Hz, calculate ripple factor for firing angle a-45" and R - 100 9. (A) I (C) 1.21
47. A series resistance-capacitance (R-C) circuit is connected to 230-volt, 50 cycle AC source. The current through the resistor is 45.45 A and the power taken by the circuit is 5,000 watts. Compute the following: a. Voltage drop across the resistor b. power factor angle c. circuit impedance