Length of one side and bearing of another side unknown or missing

Q: In a simply-supported beam loaded as shown below, the maximum bending moment in Nm is 1000 mm 500 mm…

A:

Q: Beams

A: GIven beam as shown

Q: 180.0 40.601 7. One grid line = 1 foot. 2. Draw the arrows and label the reaction forces. Label the…

A:

Q: Identify and circle 2 Simply Supported Beam and 2 continous Beam at structural drawing

A: To Identify 2 Simply Supported Beams and 2 Continuous Beams in the given structure.

Q: Problem 4 For the set of data of a closed compass traverse shown, determine the bearing of each…

A: To Determine The bearing of each line, The linear error of closure, The direction of the side of…

Q: 2.8 A roof purlin, supported by a rafter, must support a 300# vertical snow load. Determine the…

A: Given: The snow load is 300#. Consider the figure,

Q: 4225- CAR FORCH 4225- -5150- FORCH 0.00 000 DINING ARA 00000 ENRY PORCH -5150- 15150- 1550-18002425…

A: To Identify and circle 1 Simply Supported Beam and 1 continuous Beam at the structural drawing given…

Q: Determine (approximalely) the forces in each truss member and column of the portal frame. Assume all…

A:

Q: Stations Northings Eastings A 75.00 250.00 В 425.00 150.00 C 678.00 450.00 D 675.00 675.00 E 425.00…

A:

Q: A California freeway has four lanes in each direction and carries a traffic volume of 4000 veh/h.…

A: Given data: Traffic volume- 4000 veh/hright shoulder lateral clearance- 5 ft Lane width= 11…

Q: Describe about the steel sheeting sections.

A: steel sheeting section:

Q: Consider the following given portal frame: 5m 10 m 100 If the rotational displacements of joint B…

A: The given frame is shown below.

Q: 2. Determine the horizontal and vertical components of the pin forces at points B, C, and D of the…

A:

Q: Compute the width of the base.

A:

Q: Make whatever changes or addition are necessary in each case to form a correct and complete FB.D.

A: 1) Incorrect, weight mg will act downwards 2) Incorrect, there will be frictional force acting at…

Q: Draw the front, Side and top

A: For this, we can draw the diagram in Autocad. I have used the same to draw the diagram and have…

Q: 7-84. Draw the shear and moment diagrams for the beam. A 40 kN/m 8 m B. 3m 20 KN 150 kN - m

A: Given section :

Q: The Fink truss supports the loads shown in (Figure 1). Approximate each joint as a pin. Suppose that…

A: FORCE IN EACH MEMBER OF TRUSS?

Q: Drawing B INSTRUCTIONS: USE M12 BOLTS GRADE 4.6/5 INCLUDE BOLT GAUGE DISTANCES AND EDGE DISTANCES…

A: Planning is the process of setting goals, defining strategies, and outlining the steps or actions…

Q: Problem 1. From the open compass traverse shown, if the forward bearing of line AB is N 45°20' E,…

A:

Q: Determine the approximate axial forces, shears, and moments for all the members of the frames loaded…

A:

Q: The bearing of a line AB in a closed traverse ABCA is 137°30' and its length is 125.8 m. The…

A: Bearing of line AB: 137°30′Length of line AB: 125.8 mX-coordinate of point A: -5 mY-coordinate of…

Q: Part II. Beams 4. Draw the shear and moment diagrams for the loaded cantilever beam where the end…

A:

Q: Problem 1: A reverse curve has a radius of the curve passing through the P.C. equal to 200m and that…

A:

Q: roof framing plan, truss details (wood

A: The construction of roof framing plan truss is a very complex task. All the required resources must…

Q: DRAW THE FBD AND JOINTS OF ALL. PROVIDE CLEAR SOLUTION. DO NOT COPY SOMEONE'S ANSWER

A:

Q: Draw a complete, clearly labeled, FBD of member AE.

A: Draw a complete, clearly labeled, FBD of member AE.

Q: STA sa 1.24 BM-a 234.51m TP- 1 1.11 3.40 1+ 00 4.6 1+25 2.8 3.6 1+50 1+75 2.4 TP-2 3.21 2.46 2+00…

A:

Q: aw the FBD o

A:

Q: Problem 2: The long chord from the P.C. to the P.T. of a compound curve is 300 meters long and the…

A:

Q: contrast Portal Method and Cantilever Method.

A: The Portal and Cantilever method are used for analyzing the framed structure subjected to lateral…

Q: PROBLEM SET 2. Example of Omitted Measurements: Bearings of two sides Unknown Line Distance Bearing…

A:

Q: 64 38 75 50 13 30 22 35 مطو لیاسان 25 مثقوب تمرين 8.3 54 المطلوب الاما 35

A: Finding out top, front and side view.

Q: By inspection, determine the zero-force members in each truss. Identify the zero-force member by…

A: (NOTE: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Compute the net area of the given member.

A: The given figure is shown below:

Q: 2. What is required to transfer points to the ground, while chaining along the sloping ground? *

A:

Control Survey and Geodetic reductions

Control surveys or survey controls are used to establish reference points as a basis for various construction activities. Vertical and horizontal control points are to be established in a control survey to increase accuracy. After establishing the control points, all other types of surveys such as topographic, right-of-way, aerial mapping, construction layout, boundary surveys, and utility mapping can be worked upon so that control networks can be formed. The place from which the observations are made is called a survey station.