Learning Goal: To determine the effects of certain geometric shapes, namely fillets and circular cutouts, on the stress distributions inside a rigid body and to determine the maximum applicable axial force in the same rigid body while considering these stress concentrations. The member shown below is made of steel (oallow = 20.0 ksi ) that is 2.75 in thick. The member is subjected to an axial force P that is applied at both ends. Let r = 1.25 in , w = 5 in , h= 2.5 in , and d =1 in

Learning Goal: To determine the effects of certain geometric shapes, namely fillets and circular cutouts, on the stress distributions inside a rigid body and to determine the maximum applicable axial force in the same rigid body while considering these stress concentrations. The member shown below is made of steel (oallow = 20.0 ksi ) that is 2.75 in thick. The member is subjected to an axial force P that is applied at both ends. Let r = 1.25 in , w = 5 in , h= 2.5 in , and d =1 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three strain gauges are attached on the surface of the plane frame which is shown in Figure. The angle between each strain gauges are θº=69º. Reading from these gauges are: εa= 1100 μ, εb =305 μ and εc = -240 μCalculate:(a) The principal strains(b) The maximum shear strain
The state of stress at a certain point in a stressed body is as shown in the figure. Normal stress in x-direction is 80 MPa (Tensile) and in y-direction is 40 MPa (Compressive). The radius of the Mohr's circle for this state of stress will be O, = 40 MPa O, = 80 MPa + Ox = 80 MPa Oy = 40 MPa (а) 60 MPа (b) 40 MPa (c) 20 MPa (d) 10 MPa
I need the answer quickly
The strain of a component, which has a tensile modulus of 3 X 105 MPa, and subjected to a stress of 5000KPA, is .a 0.0000167 .b 0.0000176 .C 0.000167 .d 0.00176
Triangular wedges stresses.
CIVIL ENGINEERING
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume'stress magnitudes of 5,-80 MPa, S - 220 MPa. Sy For the given state of stress at a point in a structural member, determine the center Cand the radius R of Mohr's circle. Answers: C- MPa, R- i MPa. Save for Later Part 3 Determine the principal stresses (api > Op2 ) for this state of stress. Answers: Opl = MPa, o,2 = MPa Save for Later Part 4 For this Mohr's circle, determine the magnitude of the central angle between: (a) pointxand the point representing the principal stress opl- (b) point x and the point representing the principal stress Op2. (a) Angle - i (b) Angle - i
Q.41 For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 2 44 4 4 4 2
2.27. The stress components at a given point in an engineering component are es- timated to be oxy=4.1 ksi, ơyy=0 ksi, ơz =0.9 ksi, ory =-3.1ksi, ơyz = 1.2 ksi, Ozx =0 ksi. Estimate the factor of safety against yielding using von Mises' theory if the uniaxial yield stress of the material is Sy =17.2 ksi.
a. At a point in a given material the three dimensional state of stress is given by ox = oy oz = 10 MPa ,Txy F 20 MPa, Tyz = %3D !! TXZ = 10 MPa. Compute the principle planes if the corresponding principles stresses are, ol = 37.3 MPa, c2 = 10MPA, o3 =2.7 MPa %3D %3D b. , What no
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.21 in.? and an elastic modulus of 2350 ksi. Bar (2) has a cross-sectional area of 1.032 in.? and an elastic modulus of 4100 ksi. Assume L1=20 in., L2=49 in., Q=7.1 kips, P=2.9 kips, and R=12.9 kips. Determine the horizontal deflection of end C relative to end A. P (1) (2) C В L1 L2 Answer: uc/A in. %3D