le = 30° 200 mm 200 mm P= 12 kN |Н G -F 200 mm B. 200 mm 0 = 30° Prob. 6–88

Q: Q The two-steel shaft shown in figure have the same diameter and weight 170 Ih cach. Neglect the…

A: Let the normal reaction at point C = NcThe reaction of the wall at D = N2And the reaction by wall at…

Q: The square-threaded screw has a mean diameter of 20 mm and a lead of 4 mm. If the weight of the…

A: Given: The mean diameter of square-threaded screw d, is 20 mm. The length of lead l is 4 mm.…

Q: Two identical spheres weighing 100 KN each are placed in a container such that the lower sphere will…

A:

Q: mine the reactions at the roller B, the rocker C, and where the beam contacts the smooth at A.…

A: Force, Force, To find:Part A: The magnitude of reaction at A Part B: The y component of the…

Q: mplete solution pls answer in 20 m

A: Take moment about C∑ Mc=0TBA0.125-10000.3=0TBA=2400N∑ Fx=0TBA-Cx=0Cx=2400N∑ Fy=0 Cy=1000N…

Q: In the truss shown, A =1000 mm2, E = 200 GPa and the coefficient of thermal expansion is 12 x10…

A: Given Data: A = 1000 mm2E=200 Gpa   = 200×103 MpaCofficient of thermal expansionα=12×10-6/°CTo…

Q: Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force (P) is…

A: Given C=2m J=4m E=1.2m Theta=60° S.G=0.82

Q: The assembly of pipes consists of galvanized steel pipe AB and BC connected together at B using a…

A: Given G= 83Gpa AB and BC PIPE   dia of AB = outer 20mm and inner 17mm Dia of bc = outer 15mm and…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: Determine the resultant of the four forces that set on the machine element shown. Indicate the…

A:

Q: 3.36 The torques shown are exerted on pulleys B, C, and D. Knowing that the entire shaft is made of…

A: G=27 GPa=27×109 Pa LBC=0.8 m LCD=1.0 m

Q: The weight of the suspended object is W = 52 lb (Figure 1)

A:

Q: There is a small initial clearance A= 5 mm between the left end of the beam and the roller support…

A:

Q: The 8.5-kg uniform rod is pinned at end A. If it is also subjected to a couple moment of 50 Nm. The…

A:

Q: 40. A uniformly tapered aluminum-alloy tube AB of circular cross section and length L is fixed asun…

A:

Q: Q1) Determine the reactions at all supports in the beam shown. The support at A is displaced…

A: Given a continuous beam having support A settled by 100mm (0.1 m)  EI = 200*5 KN-m² Required…

Q: The wire BC has a diameter of 3.5 mm. Determine the vertical displacement of the handle at D if the…

A: Given data, Load P= 3000 N Diameter of wire BC= 3.5mm Modulus of Elasticity (E)=150 GPa =  1.5× 105…

Q: The frame shown consists of two members AC and BD connected by a pin at C. the frame is loaded as…

A:

Q: 4B.) The cylinder as shown below weighs F÷2 N. It is supported by a rod with a cable at point B.…

A:

Q: Problem #2: 300 mm-- - 400 mm- A 13 12 60° х (N) Y (N) 5. Determine the horizontal reaction at A.…

A:

Q: F-390# A 16.5 5 ו ור į 7.5 Sense of moment due to force F about point A is Counter-clockwise…

A:

Q: The 39 kg drum is suspended from the hook mounted on the wooden frame. Determine the state of normal…

A:

Q: Prob. 2. For the rigid frame loaded as shown, determine the reaction components using either the…

A:

Q: . In the figure below, the boom AC is supported in a ball and socket joint at C and by the cables AD…

A:

Q: A rigid beam loaded with negligible mass is pinned at B and is supported by two indentical rods,…

A: Take Moment at B zero Deflection will be in ratio of distance from B

Q: Determine the vertical reaction at support B in kN-m. w = 15 kN/m L1=7m L2=4 m L1 W L2 B

A:

Q: Note: Express your answer in terms of the units. Observe 3 decimal places. The error threshold is…

A: For any mechanism problem when it rested on the ground or at the sloping surface then it shows the…

Q: by assemb engineers can rotate in a vertical plane combined effect of gravity and a couple M od BC.…

A: Given:- mass=2.25kg of slender rodAB 1.85kg slender rod BC pin at B chord AC tension in chord…

Q: The pliers are used to grip the tube at B as shown in (Figure 1). A force of F = 28 lb is applied to…

A: Take moment about A∑ MA=0-28(10)+RB(1.5)=0RB=186.667lb

Q: DETERMINE THE RESULTANT OF THE FORCES SHOWN. THE COORDINATES ARE IN METERS.

A: In order to solve the given problem, the given forces are broken into rectangular components along…

Q: 6- Replace the two wrenches and the force acting on the pipe assembly, by an equivalent resultant…

A:

Q: and II numbered cylinders with radii r = 2m and weight W were connected to each other with the help…

A: Whole system is symmetrical so forces will also be same on both sides and central sphere make…

Q: Situation A (1 - 4) A cylindrical pressure vessel is constructed from a long, narrow steel plate by…

A:

Q: , GE, and GD of the cage system for the loading condition given in Figure 2 Calculate the rod…

A:

Q: Determine the reactions at the supports of the beam. Assume that support at B is a roller and EI is…

A: Some standard formula for slope and deflection.

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.