LA J Z₁ lc Three-phase source Feeder lines Balanced load the above circuit diagram, we have source impedance Zg = 0.05+j0.15 ohm, Z, = 0.1+j0.2 ohm and per phase impedance in the alanced Delta connected load, Z₁ = 12+j9 ohm. RMS value of source voltage is 200 volt. Phase sequence is as shown in the diagra EMS value of current lc = ampere Phase angle of lc = degree RMS value of line voltage VCA = V₁4-120 V4120 volt Inc ICA

LA J Z₁ lc Three-phase source Feeder lines Balanced load the above circuit diagram, we have source impedance Zg = 0.05+j0.15 ohm, Z, = 0.1+j0.2 ohm and per phase impedance in the alanced Delta connected load, Z₁ = 12+j9 ohm. RMS value of source voltage is 200 volt. Phase sequence is as shown in the diagra EMS value of current lc = ampere Phase angle of lc = degree RMS value of line voltage VCA = V₁4-120 V4120 volt Inc ICA

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

consider the following diagram of impedances in per unit of a common base a) get the YBUS admittance array and the ZBuz impedance array 213-j2 pu zt2-j0.15 zg2-j1.85 791-j0.9 211-0.1 1 212-j0.5pu 223-j0.5pu Va 1 p.u. Jv1-1p.u. 22-10 pu
3.n Figure 3P.2 shows two capacitor banks, C, and C2, in a substation C is enercized, but C, is discharged. The three-phase, 60 Hz ratings of the banks are: C,, 5 MVA; C,, 3 MVA, on a 13.8 kV base. The source has a short circuit rating of 20 kA rms at 13.8 kV. The inductance of the loop between C, and C,, represented by L, is 30 µH. 13.8 kV V3 L L2 o to C2 Source Capacitor banks ouG OL 19 Fig. 3P.2. Calculate the peak transient voltage that will appear on C, and the peak transient current that will flow in L,, if the switch S is closed at the peak of the voltage cycle. Point out any assumptions you make.
In a given system of base power of 250 MW, and bus 3 is taken as reference. The per-unit reactances are X₁2 = 0.2 p.u., X13 = X23 = 0.1 p.u. If the power flow in the system is given as: PF12 = 100 MW, PF13 = 50 MW, PF23 = -150 MW, then the phase angles are Select one: O a. 0₁ = 0.02 rad., 0₂ = 0.06 rad., 03 = 0 rad. O b. None of these O c. 8₁ = 0.02 rad., 02 = -0.06 rad., 03= 0.1 rad. O d. 0₁ = 0.02 rad., 02 = -0.06 rad., 03 = 0.2 rad. O e. 8₁ = 0.02 rad., 8₂ = -0.06 rad., 03 = 0.1 rad. O f. 0₁ = 0.02 rad., 02 = -0.06 rad., 03 = 0 rad.
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
Q2
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the RMS line current at load 1 and 2 respectively?
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
= = Impedances Z₂ and z3 in parallel are in series with an impedance z₁ across a 100V,50Hz AC supply. Z₁ (6.25 +j1.25)ohms, Z₂ = (5 + j0)ohms and Z3 (5 - jxc)ohms. Determine the value of capacitance Xc said that the total current of the circuit will be in phase with the total voltage. What is then the circuit current and power?
i need the answer quickly
In the figure, bus 1 is the reference bus, V1 = 1.06 p.u and the angle is 0.. A load with active power= 100 MW and reactive power = 50 Mvar is connected to bus 2. The line impedance is z12 = 0.12 + j0.16 p.u on a base of 100 MVA. Start with an initial estimate of |V2|0) = 1.0 p.u and 820) = 0•. Find |V2| () (one iteration). 100 MW 212 = 0.12 + j0.16 ++ 50 Mvar Vị = 1.0/0° О а. |V2| (1) = 0.4 p.u. Ob. |V2| (1) = 0.5 p.u. Oc. |V2| (1) = 0.7 p.u. d. (1) = 0.8 p.u. е. |V2| (1) = 0.6 p.u.
Impedances Z1 = 5.83 at angle of -59 deg. and Z2 = 8.94 at an angle of 63.43 deg. are in series and carry an effective current of 5A. Determine the Power and power factor of the circuit indicating if it is leading or lagging.
In power distribution systems, what is sometimes necessary to install to reduce harmonic frequencies and distortion between the three-phase transformers and distribution panels?