LA = 2600 mm2 1000 mm E = modulus of elasticity = 200 GPa a = coefficient of thermal expansion

Q: A thin plate of linear elastic materials (E v = 0.25) is in plane stress (o, = Txz = Tyz = 0). The…

A: Given that, Modulus of elasticity of the material, E=200 GPa,Kinematic viscosity of the material,…

Q: The two cylindrical rod segments shown in the figure below (Eigure 1) are fixed to the rigid walls…

A:

Q: At a temperature of 15˚C, a steel bar just fits between two rigid supports. Its length is L = 5 m,…

A:

Q: A closed cylinder (26 + 60) cm long, containing 3 MPa pressurized fluid, due to this pressure a…

A: Since we provide answers up to three subparts only, we will answer the first three subparts here.…

Q: A copper cylinder 150mm outside diameter has walls 25mm thick. End plates are stayed by a 25mm…

A: Given Data :-  Outside dia = 150mm Walls thickness= 25mm Temp = -11  Atm temp = 100

Q: A stepped bar is subjected to an axial tensile force of 40000 lb. Compute the increase in stress due…

A:

Q: Q2\ Find the necessary change in temperature in the copper bar so that the rigid bar remains…

A: For the rigid bar to remain horizontal, the moment due to the UDL should be equal to the moment due…

Q: * Fixed-Fixed bar was 20 centigrade degree at room temperature, Determine the thermal stress when…

A: Given data as per the question The initial temperature of the bar = 200 c The final temperature of…

Q: "he rigid bar of negligible weight is supported as shown. The assembly is initially stress-free.…

A:

Q: 2.77 A steel rod 3 ft long with a cross-sectional area of 0.3 in.² is stretched between two fixed…

A:

Q: A thin bar of length L = 3 meters is situated along the x axis so that one end is at x = 0 and the…

A: Given: Length, L=3m Thermal diffusivity, k=0.4 Initial temperature, f(x)=100-10x Boundary…

Q: The two cylindrical rod segments shown in the figure below (Figure 1) are fixed to the rigid walls…

A:

Q: A copper cylinder 150mm outside diameter has walls 25mm thick. End plates are stayed by a 25mm…

A:

Q: A 1 m length bar of square cross section with side length 2cm, . is fully supported at one end and…

A: To find: The maximum force that bar can sustain elastically. Given: The length of the bar is l=1 m.…

Q: Steel railroad reels 12 m long are laid with a clearance of 2.5 mm at a temperature of 20°C. At what…

A:

Q: 9. The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure.…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: A steel bar AD has a cross-sectional area of 260 mm² and is loaded by forces P, = 12 kN, P, = 8 kN,…

A:

Q: The bar will induce

A: No stress (A)

Q: Compute the stress in the bar.

A: Here,  is strain developed in the bar. is compressed length. is initial length of the bar.. is…

Q: Compare the use of a low-strength, ductile material (1018 CD) in which the stress-concentration…

A: The forces acting on the material are-The factor of safety at point A if  Q&T  material is used…

Q: A rod with a cross sectional area of 125 mm2 is stretched between two fixed points such that the…

A:

Q: A square piece is initially at 10 degrees Celsius everywhere. Each side is 0.05 m long. Then the…

A: To solve this problem, we can use the heat equation to model the temperature distribution in the…

Q: Q-A steel rod is heated from 30° to 80°C and free expansion of rod is allowed while heating. If…

A: A steel rod is heated from 30° to 80°CFree expansion of rod is allowed while heating.The coefficient…

Q: A 1m long steel bar (E=200GPa) of 10mmx10mm dimension fixed at both ends is heated to 90°C from…

A:

Q: - 20 °C Wood siding Stud 130 mm Insulation Wall board 21 °C 40 mm Figure 1: The top view of the…

A: Assumptions: (i) Steady state conditions (ii) Temperature of composite depends only on x (iii)…

Q: A copper cylinder 150mm outside diameter has walls 25mm thick. End plates are stayed by a 25mm…

A:

Q: A steel tube is restrained between two rigid walls 80 cm apart, At a temperature of 28 degree…

A:

Q: As shown, there is a gap between the aluminum bar and the rigid slab that is supported by two copper…

A:

Q: A steel rod with a radius of 2.5 cm, the ends of which are fixed, is subjected to a tension force of…

A:

Q: As shown in Fig, there is a gap between the aluminum bar and the rigid slab that is supported by two…

A: Given data as per question Area of copper rod =500 mm2 Area of aluminium rod =400 mm2 we know that…

Q: A solid body of length L with a rectangle cross section has a temperature distribution equals to : T…

A:

Q: A custom-fabricated component for a machine consists of a steel (y = 0.28 lbf/in?), 5-in diameter…

A: The mass of the solid steel cylinder without any hole pattern is The mass of the bronze part is…

Q: 2. A steel rod having modulus of elasticity of E=200x10 MPa, thermal expansion of a-11.7x10/°C and…

A:

Q: An assembly of a steel bar enclosed within an aluminium alloy tube is shown in Figure 1(b). The tube…

A: Tensile strain is the deformation or elongation of a solid body caused by a tensile force or stress.…

Q: A metal wire has the following properties. Length= Im, Initial temperature 0,125cal/gC, Thermal…

A: When heat flows in only one direction, it is known as one dimensional heat flow. General equation…

Q: A bronze bar 3 m long with a cross-sectional area of 320 mm² is placed between two rigid walls as…

A: Given    Area, A = 320 mm2 Length, L = 3 m         Gap = 2.5 mm             E = 80 GPa Find…

Q: Consider a steel bar attached at both ends. Assume that at 20 °C this bar is free of tension.…

A: Thermal stresses generated due to a temperature increase fromT1 to T2  is given byσ=E∝ T2-T1where…

Q: A rigid bar of negligible weight is supported as shown in Fig. P-271. If W = 80 kN, compute…

A:

Q: (E, = 200 GPa, a, =11.7×10°C) have the dimensions shown at a temperature of 20°C. The steel rod is…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.