kPaa, 26.7 °C to 827.36 kPaạ. All clearances are 8%. a. Determine the isentropic power for single stage compression ANSWER b. Determine the piston displacement required for single stage compression ANSWER c. Using the same data: find the minimum ideal work for two stage compression when the intercooler cools the air to the initial temperature ANSWER d. How much heat is exchange in the intercooler? ANSWER

kPaa, 26.7 °C to 827.36 kPaạ. All clearances are 8%. a. Determine the isentropic power for single stage compression ANSWER b. Determine the piston displacement required for single stage compression ANSWER c. Using the same data: find the minimum ideal work for two stage compression when the intercooler cools the air to the initial temperature ANSWER d. How much heat is exchange in the intercooler? ANSWER

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At the beginning of compression, Otto cycle works on 0.2 lb/s of air at 14 psia and 1300F. The temperature at the completion of combustion is 45000R, the compression ratio is 5.5, and the hot-air standard is k = 1.3. a. Find V1 , P2 , T2 , P3 , V3 , T4b. Compute the heat added (QA),heat rejected (QR), work (W) andthe cycle efficiency (e).
pls answer all i will give thumbs up if right
May I get help with this question please?
Show the ts and pv diagram. Show complete and step by step solution. Box the answer
The compression ratio in an air standard Otto cycle is 9. At the beginning of the compression stroke, the pressure is 0.1 MPa and the temperature is 21 C. The heat transfer to the air per cycle is 2000 kJ/kg. Use the PG model for air. I am trying to find the Mean Effective Pressure from this information
Show the ts and pv diagram. Show complete and step by step solution. Box the answer
An air-standard dual cycle has a compression ratio of 9.1 and displacement of Va= 2.2L.At the beginning of compression, p1= 95 kPa, and T = 290 K. The heat addition is 5 kJ, with one quarter added at constant volume and the rest added at constant pressure. Determine: a) each of the unknown temperatures at the various states, in K. b) the net work of the cycle, in kJ. c) the power developed at 3000 cycles per minute, in kW. d) the thermal efficiency. e) the mean effective pressure, in kPa. Step 1 Your Answer Correct Answer (Used) Determine each of the unknown temperatures at the various states, in K. 684.1 K T3 = K 1217 T4 = 2311 K 1440 K Step 2 X Your answer is incorrect. Determine the net work of the cycle, in kJ. Weycle = I 3.470026652 kJ Hint Save for Later Attempts: 1 of 3 used Submit Answer Step 3 The parts of this question must be completed in order. This part will be available when you complete the part above.
A Brayton cycle inlet is at 300 K. Inlet and exit temperatures of the turbine is measured as 1800 K and 710 K, respectively. The compressor pressure ratio is 13. Use cold air-standard approach to calculate the thermal efficiency of the cycle. BURNER- COMPR. TURBINE a. 0.35 O b. 0.40 C. 0.45 d. 0.50 e. 0.55 f. 0.60 g. 0.65 Seçimimi temizle
An air-standard Compression Ignition cycle has a compression ratio of 18.2. Air is at 32000R at the end of the heat addition process. Neglecting the variation of specific heats with temperature,determine the following:a. Cut-off ratiob. Net output work of the cyclec. Heat rejection per unit mass, Btu/lbd. Thermal efficiency of the cycle(%). Compare this efficiency value if the cycle has to run on an airstandard Carnot Cycle.
An engine operating on the Otto cycle principle has an initial compression temperature of 675°C and a compression ratio of 8. The pressure at this condition is 100 kPa and the cylinder volume is 0.028 m³. The maximum temperature that can be achieved by the system is 4500°C. a.)Calculate the temperature and pressure at each end of the process (point), B. thermal efficiency, C. MEP
A spark – ignition engine has a compression ratio of 8.5 and a maximum temperature of 945.15K. At the beginning of compression stroke, P and T of the fluid are 0.1 MPa and 28.65 deg C. Assuming hot air-standard analysis, how much work (kJ/lb) is produced per cycle completion?
Hello, this is the problem attached below: An air-standard dual cycle has a compression ratio of 8.6 and displacement of Vd = 2.2 L. At the beginning of compression, p1 = 95 kPa, and T1 = 290 K. The heat addition is 4.75 kJ, with one quarter added at constant volume and the rest added at constant pressure. Determine: a) each of the unknown temperatures at the various states, in K.b) the net work of the cycle, in kJ.c) the power developed at 3000 cycles per minute, in kW.