Knowing that the tension in wire BD is 1340.0 N, determine the reaction at the fixed support Cof the frame shown. 750 N 150 mm 250 mm -500 mm varded B red 450 N 600 mm 400 mm D The reaction at Cis 1988 88 The moment at Cis -326 N-m ).

Q: why is NB=0

A:

Q: Detrmine the speed of rotation of the output shaft in figure below and its direction of rotation…

A: Write the expression of the gear ratio of gears A and B.

Q: could you pls provide part D and E

A:

Q: D'Alembert's principle is an application of O a. Law of Inertia O b. Newton's third Law O c.…

A: D’alembert’s principle: It states that the sum of the differences between the forces acting on a…

Q: State an equation tha relate the number of teeth of gear D, B and C.

A:

Q: How can we locate the position of the neutral axis?

A: Suppose a beam undergoes sagging bending, in this type of bending the upper surfaces undergoes…

Q: can you resolve??

A: Power for first turbine Power  for second turbine To find the power output of the device and power…

Q: e

A: given:RPM N=2000time of injetion =0.0015

Q: b) Find the critical radius "rc" as we called in class in terms of

A:

Q: What does the internal moment cause?

A: Internal moment are actually the moments due to the resisting forces generated when the cross…

Q: Q1/ Number the links on two of the mechanisms shown in Figures (1 & 2 & 3 & 4 & 5) then, calculate…

A:

Q: mm.

A:

Q: 8(unich is The best-sited material for Commutator Segments.

A: Given Data⇒Commutator segmentsProblem definition⇒Problem says which is best suited material for…

Q: 04: Complete the secetion of the reciprocating pump (shown in figure.2) by adding the details of the…

A: Gear box in the reciprocating pump The purpose of the gearbox is to convent rotating energy to…

Q: When does the moment area method seem to be convenient?

A: The moment area method is convenient when the beam's deflection or slope has to be estimated at a…

Q: Refer to the figure to the right. The 4-way valve has a blocked center spool and three positions.…

A: when the solenoid B is energized the cylinder 1 retract to the left and cylinder 2 extend to the…

Q: -d12 The figure shows a tabletop experi- nent that can be used to determine an unknown homent of…

A:

Q: 02: Fully describe the gyroscopic effects on ships.

A: The front side of the ship is known as a bow and the rear end (the end where the rotor is present)…

Q: Qu write Bernoullis Equation for given tigure 2

A: Energy at any two point in moving fluid is same .  Energy 1= Energy 2…

Q: B) The Hoist drum shown in Figure 2 below is driven by a four-stage gear reducer. The input gear A…

A: combining information from two images

Q: Give the answer with proper explanation why you chose that specific option. Thank you

A: Given: Here is the torque curve is shown here, To find: Determine the representation of Torque…

Q: Define the termTruss?

A: The truss is a structure that is used to distribute the load. It is made by combining members into…

Q: What is the Flexure Formula?

A: The stresses in the beam caused by the bending moment is called as flexural or bending stress.

Q: what is the omega value? as per the professor, the IC is at b not a

A: Given: The velocity of the upper wire: →V=5.6 m/s It is right that the instantaneous center of…

Q: Specify the location of all velocity centers in the following mechanism.

A: for solution refer below images.

Q: What is the name of the circle from which the involute curve is generated? Select one: O a. Base…

A: Involute Curve: The involute curve is a type of mathematical curve. The involute curve is often used…

Q: What is the vertical component of the velocity of point B? Let a positive velocity be up What is…

A:

Q: Derive the expressions for A, B, & C in the given figure with the help of clear drawing and stepwise…

A:

Q: Gear Train (more than 2 gears in a line) - In this scenario, a motor is attached to a wheel through…

A: Spur gear- Pure rolling motion is transmitted between two cylindrical surfaces in contact. It is…

Q: Question 1: Gears  The lath machine in the Central University of Technology (CUT) mechanical…

A:

Q: The number of DOF

A: Given; links, l = 10 joints, j =12 Simple revolute joint ?

Q: at is the angular velc Gear 4 rotates in

A:

Q: How can we find the location of the neutral axis?

A: When a bending moment is applied on a beam, normal stresses are set up in its cross-section due to…

Q: When can the moment-area method be used?

A: The moment area method is used to find the deflection and slope at a particular point in the beam.…

Q: Given: L¡ = 7.25 in., L2 = 2.00 in., L3 = 7.00 in., L4 = 4.50 in., 01 = 5°, and 02 = 150°.…

A:

Q: The shown picture is for 12-cylinder engine. The piston number 5 is connected to bearing denoted by

A: Piston 5 is connected to the bearing denoted by 10 on the crank shaft

Q: In the drawing, arm A is being driven back and forth in the direction of the arrows. It is connected…

A: Solution: Given Data: Screw B is lowered towards the end of arm A.   To Find: What happens to the…

Q: The figure below shows the components of normal forces, the value of radial force on the gear wheel…

A:

Q: The number of degree of freedom of a planar linkage with 22 links and 27 simple revolute joints.

A: Answer: The number of degree of freedom is 9.