knife follower motion interval described below: 1. To raise the valve through 50 mm during 120° rotation of the cam; 2. To keep the valve fully raised through next 30°; 3. To lower the valve during next 60°; and 4. To keep the valve closed during rest of the revolution i.e. 150° The displacement of the follower being raised and lowered, is to take place with simple harmonic motion Determine: 1. The required time for each interval? 2. Draw the displacement against time, diagrams for one complete revolution of the cam.

knife follower motion interval described below: 1. To raise the valve through 50 mm during 120° rotation of the cam; 2. To keep the valve fully raised through next 30°; 3. To lower the valve during next 60°; and 4. To keep the valve closed during rest of the revolution i.e. 150° The displacement of the follower being raised and lowered, is to take place with simple harmonic motion Determine: 1. The required time for each interval? 2. Draw the displacement against time, diagrams for one complete revolution of the cam.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cam is used to operate a platform that repeatedly lifts boxes for a height of 40 mm as shown. One cycle of the cam has the following motion requirements: Rise to 40 mm in 1.5 s, Dwell for 0.25 s, Fall for 20 mm in 1 s; Dwell for 0.25 s; Fall a further 20 mm in 1s and the cycle repeats after this. The required speed of cam is rpm and the angle turned by cam during the Rise motion is degrees. *Write your answer only as numbers, DO NOT add any text 40 mm
i need the answer quickly
The following data relate to a circular cam operating a flat-faced follower :Least diameter = 40 mm, Lift = 12 mm, Angle of action = 160°, Speed = 500 rpm. If the period of acceleration of the follower is 60° of the retardation during the lift, determine the main dimensions of the cam, the acceleration at main points. What is the maximum acceleration and deceleration during the lift?
Q8: The valve timing details for an engine are: Inlet valve opens 6° before TDC and closes 38° after BDC. Exhaust valve opens 35° before BDC and closes 5° after TDC. Calculate in degrees: (a) The valve overlap (b) The lead and lag of the exhaust valve lead (c) The lead and lag of the inlet valve (d) The period of: (i) the intake stroke, (ii) the exhaust stroke.
Consider the following statements: 1. For a radial-translating roller follower, parabolic motion of the follower is very suitable for high speed cams. 2. Pitch point on pitch circle of a cam corresponds to the point of minimum pressure angle which of the statements given above is/are correct ? (b) 2 only (a) 1 only (c) Both 1 and 2 (d) Neither 1 nor 2
A cam is used to operate a platform that repeatedly lifts boxes for a height of 40 mm as shown. One cycle of the cam has the following motion requirements: Rise to 40 mm in 1.5 s, Dwell for 0.25 s, Fall for 20 mm in 1 s; Dwell for 0.25 s; Fall a further 20 mm in 1 s and the cycle repeats after this. The required speed of cam is.............rpm and the angle turned by cam during the Rise motion is...........degrees.
A Cam of base circle 60mm is to operate a follower of 25mm diameter. The follower has Simple harmonic motion. The angular speed of Cam is 360 rpm,Cam lift = 50 mm, Angle of ascent = 120, Angle of dwell =(your registration last 2 digits), Angle of return = 60, dwell for rest of the cycle. The rise of the follower is simple harmonic motion and fall of the follower is with uniform velocity. Calculate the Maximum Velocity and Acceleration during Ascent and Descent.
Do
(Figure 1) Figure JAN= (1) 1 of 1 > Determine the velocity of rod R for any angle of the cam C if the cam rotates with a constant angular velocity w. The pin connection at O does not cause an interference with the motion of A on C. Express your answer in terms of the variables T1, T2, w and 0. v = Submit | ΑΣΦ. 41. vec Request Answer < Return to Assignment 5 Provide Feedback ?