Answered: K 7.62 m A 50° 25⁰ B Y с

Engineering

Civil Engineering

K 7.62 m A 50° 25⁰ B Y с

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam is subjected to a triangularly distributed load of Q = 9.3 kN/m over segment length L = 1.1 m. Determine the maximum slope and deflection of the beam ₁Q kN/m A AT DI L L
Problem: A gravity dam in the figure carries water that is 12 m deep on its upstream side. The coefficient of friction between the soil and the dam is 0.50. y_concrete=23.5 kN/m^3 a. How far is the vertical resultant force from the toe? b. What is the factor of safety against sliding? c. What is the factor of safety against overturning? d. What is the soil pressure in heel? e. What is the soil pressure in toe? 4m 12m 3m 2m T. (om
Problem: A gravity dam in the figure carries water that is 12 m deep on its upstream side. The coefficient of friction between the soil and the dam is 0.50. y_concrete=23.5 kN/m^3 a. How far is the vertical resultant force from the toe? b. What is the factor of safety against sliding? c. What is the factor of safety against overturning? d. What is the soil pressure in heel? e. What is the soil pressure in toe? 4m 1 12m 3m 2m - lom-
Consider a slope given below with 10 slices, which has a circular failure surface. Each slice has 5 meters wide, and the weight of each slice was estimated on the basis of average height and a unit weight of soil ? = 16 kN/m3. The shear strength of the soil is assumed to be ? = 20 kPa and ? = 20°. The pertinent data for these ten slices is given in the table below. a) Determine the factor of safety using Janbu’s simplified method by assuming the initial ?? = ?. ?. b) Discuss how the factor of safety (stability of the Slope) will change due to the rainfall. You start to consider what environmental conditions will change first.
I need this soluttion urgent ,please solve
The figure below shows a slope with an inclination of B = 56°. If AC represents a trial failure plane inclined at an angle 0 = 33° with the horizontal, determine the factor of safety against sliding for the wedge ABC. Given H = 8.4 m; y = 20 kN/m³: ' = 21°; and c' = 36 kN/m?. (Round your final answer to two decimal places.) F, =
A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of 17 kN/m³ and an undrained shear strength cᵤ = 20 kPa. The slope make an angle of 60° with the horizontal. Assume stability number m = 0.185. Slope failure occurs along the plane AC with BC = 8 m. Which of the following most nearly gives the stability factor?
Q\ Calculate the uplift pressure at point E2 shown in the figure below using Khosla's theory. 68 m 62 m 10 m- E1 C1 56 m D1 6 m ++6m+ 2 3 3 m E2 C2 57 m D2 + 6 m 60 m E3 C3 52 m D3
A gravity dam in the figure carries water that is 12 m deep on its upstream side. The coefficient of friction between the soil and the dam is 0.50. γ_concrete=23.5 kN/m^3 a. How far is the vertical resultant force from the toe? b. What is the factor of safety against sliding? c. What is the factor of safety against overturning? d. What is the soil pressure in heel? e. What is the soil pressure in toe?
Q1. The given structure is supported by a fixed support at point A, a pin support at point D and a roller support at point E. What should be the value of P in order to have a horizontal displacement of 0.01m at point B? Use the Slope Deflection Method for solution. Assume axial rigidity and take EI=10000 kN.m². P 4 m (21) B 3m 30 kN (1¹) 3 m C. 4 m (21) D 4 kN/m 3 m (1) E
For the beam loaded as shown in the figure 3, determine the slope at B in degrees using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 5.5 m, b = 3.3 m, c = 20.3 kN/m, d = 27 kN.
Q1:A reinforced concrete tank * has a bottom plate (foundation) which assumed to be sliding (hinge), find the magnitude that used for drawing the Tangential Force, and then find maximum shear force, using the following data: Diameter (D) =9014mm, Height (H)=8000mm, Thickness (t)=335mm,Poisson ratio (v)=0.25, yw=10KN/m3=1x10-5 N/ mm3