k - 10 N/m 2 m Spring is originally compressed 3 m. (f) 100 N -2 m

Q: zain IQ İlı. Saly ibäi The units of length,mass,time-13 are a- Fundamental units. O b-Derived units.…

A:

Q: A simply supported steel beam EVEN: 12m long carries a uniformly distributed load of 22KN/m load…

A:

Q: On the drawing (attached , apply a datum feature symbols to create a datum axis A-B by using the…

A: The given data is: For left side: Shaft Diameter Upper Limit=9 6.40 mmShaft Diameter Lower Limit=ϕ…

Q: B 7m |C A 5m 6m 8m

A: Given: A tank filled with lubricant oil exerting 150 kPa Required: To find vertical stress increase…

Q: Explain the CORS system.

A: The CORS System stands for Continuously Operating Reference Stations (CORS). It enables…

Q: Given the two orthogonal projections of the object (top view and front view), identify the third…

A: Data given Find the side view

Q: The beam shown in Figure 1 supports a distributed live load of 1.5 kN/m, and a single concentrated…

A: Live load = 1.5 KN/m  Dead Load = 2 KN/m  Single concentrated load = 10 KN  Dimension of beam are…

Q: For the properties of wide-flange refer to the attached table. TABLE B-2 Properties of Wide-Flange…

A:

Q: Determine: a) Differential Area b)  Centroid distance along x and y axis   *use 3 decimal places…

A:

Q: 3.46 During a storm, wind exerts a pressure of 130 N/m², normal to the surface of the stop sign.…

A:

Q: p² – 3r + 2 lim r-1 r - 1

A:

Q: Y. 6" 1" 12" y 12" Figure P-7-6.8

A:

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: 1 2 T - 3 CONCACA NIDO Force diagrams - Inclined plane 5 Performs various tests by modifying the…

A:

Q: This blueprint shows the layout for rectangular ducting for a home forced airheating system. The…

A: As per out rules and guidelines we solve only first three subparts kindly resubmit the remaining…

Q: This ceiling register has equally spaced openings. a. Find in inches the width of each opening.b.…

A: Total number of opening in a row=9 spacing between the opening in row=38in Total number of opening…

Q: Determine the polar moment of inertia with respect to the centroidal X and Y axes. Present detailed…

A: Given: Required: Polar moment of inertia about centroidal x and y axes

Q: at state of given (All in The Stres point is MPa) 80 100 100 i) And Principal Stren & Principal…

A:

Q: 3. A 12m beam simply supported at 1.3m from both ends carries a uniformly distributed load of 18KN/m…

A:

Q: is required to find soil pressure at a depth of 10 ft beneath the interior corner A and exterior…

A:

Q: Identify all ZERO force members

A:

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: Q2- Find the centroid for the shaded area shown in the figure. (All dimensions in mm) 20 40 20 50

A:

Q: Draw (A.F.).(S.F.) &( B.M.) diagrams for the following problems: H 12t 5m 4m 2 1 3m 5m 4m 3m

A:

Q: AAC both of the 800 800 T 1 P 1400 b 12 R

A:

Q: 4 in 2 in 4 in 8 in -12 in- -16 in-

A:

Q: 1. Differentiate atmospheric pressure, gauge pressure and absolute pressure. 2. State the stability…

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: 6Ocm 20 29 cm

A:

Q: A 500 N 2m 120⁰ 3 m 200 N

A:

Q: Replace the force system in the shown figure by an equivalent resultant force and specify its point…

A: In vector addition, the resultant force is the result of combining a system of forces and torques…

Q: Evaluate or simplify the following expressions: (a) 8 x (b) ở $ (c) 8,8 kk ijij jk (d) &1jk 83j Vk

A:

Q: The column section shown above is reinforced with equal number of 20 mm bars on each face. Using f.…

A: Given:- The diameter of the bars used as reinforcing = 20 mm  The compressive strength of concrete…

Q: (0 KN 15KN DU む oam 0.am J 1.2met>2mt l.zmel

A:

Q: Given: |Change in length of BE=0.00352a mm Area(BE)=150a mm? E Area(CF)=150a mm? E=200 GPa Required:…

A: To find the change in length of CF-

Q: Determine the coordinates of the centroid of the lines shown with respect to the indicated X and Y…

A: Given, A section,

Q: 200N 30 R, "y at point C

A:

Q: H, = 19 mm, G, 2.51, Pa 1.73 g/cm d, = 0 division, Gauge factor = 0.01 (mm/division) Dial Gauge Dial…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: 5 10 35 30 11E 25 10 15 20 25 .001 in. 10

A: 3 English Fixed scale reading = 0.8inch 4 English Vernier scale = 16 Least count = 0.001 inch Net…

Q: 100 A 9, A3 200 1. What is the value af ybar from the 1-1 line (Select) 2. What is the value of…

A:

Q: Additional Problem: The wall crane supports a load of 7 kN. Determine the horizontal and vertical…

A:

Q: Coefficient of elasticity of a fluid E = 200000 t / m² Considering that for 1 Atmosphere (10 t / m²)…

A: Given Data : Bulk Modulus of Elasticity, (E) = 200000 t/m2  Volumetric stress = Pressure increase =…

Properties of Aluminium

Aluminum (or Aluminum) is a silvery-white in color metal. The chemical symbol of aluminum is Al and it has an atomic number (Z) of 13 in the periodic table. The aluminum name for this metal is derived from the Latin word ‘alumen’, which means bitter salt. Aluminum was discovered in the year 1825 by Hans Oersted, and later Friedrich Wöhler isolated aluminum. It is the most commonly found metal in the earth’s core, which is around 8% of the total core mass. Moreover, it is the third most commonly found element on earth after oxygen and silicon. Electron distribution of aluminum per shell is 2, 8, and 3 with a valency of 3. Atomic weight is nearly 26.9815 u.