IV. CALCULATION 1. Calculate the density as follows: m V Where: density of the liquid, g/mL mass of the liquid volume of the liquid %3D m %3D V V. DATA, RESULTS, AND COMPUTATION Room Temperature: _28.5°C_ Table 1.1 Test Results Mass of the Density of the liquid (g/mL) Mass of the Mass of the Volume of the cylinder (g) cylinder w/ liquid (g) liquid (g) liquid (mL) Liquid 1 Liquid 2 Liquid 3 Liquid 4 95 261.25 168 95 201.5 130 95 232.25 148 95 225.90 167 ADDITIONAL TASK: From the computed density using the above provided data, indicate which of the following closely represents the liquid density: Water, Kerosene, Cooking Oil, Ethanol

IV. CALCULATION 1. Calculate the density as follows: m V Where: density of the liquid, g/mL mass of the liquid volume of the liquid %3D m %3D V V. DATA, RESULTS, AND COMPUTATION Room Temperature: _28.5°C_ Table 1.1 Test Results Mass of the Density of the liquid (g/mL) Mass of the Mass of the Volume of the cylinder (g) cylinder w/ liquid (g) liquid (g) liquid (mL) Liquid 1 Liquid 2 Liquid 3 Liquid 4 95 261.25 168 95 201.5 130 95 232.25 148 95 225.90 167 ADDITIONAL TASK: From the computed density using the above provided data, indicate which of the following closely represents the liquid density: Water, Kerosene, Cooking Oil, Ethanol

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q11):: De termine the Land mass densityespecificċ volume specific weight of a Liquid whose gravitt
X L In the figure particle 1 of charge q1 = 0.92 μC and particle 2 of charge q2 = -3.03μC, are held at separation L = 9.0 cm on an x axis. If particle 3 of unknown charge q3 is to be located such that the net electrostatic force on it from particles 1 and 2 is zero, what must be the (a)x and (b)y coordinates of particle 3.
2) Knowing that 0=30°, determine the smallest value of us for which the 18 kg block is in equilibrium. 200 N 18 kg 35
The tendency of a body to keep moving once it is set in motion is called mass gravity force inertia
For gases under certain conditions, there is a relationship between the pressure of the gas, its volume, and its temperature as given by what is commonly called the ideal gas law. The ideal gas law is PV = mRT
A solid system of particles wherein the distances between particles remain essentially unchanged is called a: a. Stationary body. b. Fixed body. c. Rigid body. d. Flexible body.
The kinematic viscosity of a liquid is 6 stokes. What will the kinematic viscosity in m?/s?
A density fluid p has filled through a tank of diameter, D at a constant rate of v. The bottom of the tank has a feature of a hole with diameter of d. What is the liquid's steady-state height, h, in the tank?
Contrary to what you might expect, a solid metal ball can float on water due to the surface tension effect. Determine the maximum diameter of a ball made of material A that would float on water at 20°C with ss = 0.0730 N/m. What would your answer be for material B? Use the densities of materials A and B from the following table. Material A Zinc, density 7000 kg/m3 Material B Gold, density 19320 kg/m3
True or false
Determine the angular momentum Hp of each of the two particles about point P. Use a scalar solution. Take that mA = 2.0 kg and mp = 1.2 kg. (Figure 1) Figure A 15 m/s MA y 0 -2m- 30° 10 m/s B 5 m 1.5 m m' 4 m | mB 4 m X < 1 of 1 Part A Hp of the particle A about point P. Express your answer to three significant figures and include the appropriate units. +(HA)P= Value Submit Part B μA Submit Request Answer Provide Feedback Hp of the particle B about point P. Express your answer to three significant figures and include the appropriate units. HÅ +(HB)P= Value | Units Request Answer ? Units ?
An air–fuel mixture is compressed by a piston in a cylinder of an internal combustion engine. The origin of coordinate y is at the top of the cylinder, and y points straight down as shown. The piston is assumed to move up at constant speed VP. The distance L between the top of the cylinder and the piston decreases with time according to the linear approximation L = Lbottom − VPt, where Lbottom is the location of the piston when it is at the bottom of its cycle at time t = 0, as sketched in Fig. At t = 0, the density of the air–fuel mixture in the cylinder is everywhere equal to ?(0). Estimate the density of the air–fuel mixture as a function of time and the given parameters during the piston’s up stroke.