iv-ionization coefficients a, y are function ofa-applied voltage b-pressure and temperature c-electric field d-ratio ofelectric fieldto pressurev-The relation between breakdown strength and gap distance in liquid dielectric isb-Kdc-Kd-n d-(K₁d + K₂)Vb:a-K/dvi-Dielectric constant of mineral oils is abouta- 1.5 to 2b-2.2 to 2.4 c-3 to 3.5d-1.008vii-For a 1cm gap in air at 760 mm pressure and 20 °C temperature thebreakdown voltage is:a- 24kV b-30.3kVc-22.92kVd-40kV

Since you have asked multiple questions, we will solve the first question for you. If you want any…

iv-ionization coefficients a, y are function of a-applied voltage b-pressure and temperature c-electric field d-ratio of electric field to pressure v-The relation between breakdown strength and gap distance in liquid dielectric is V₁: a-K/d b-Kd c-Kd-n d-(Kid + K₂) vi-Dielectric constant of mineral oils is about a- 1.5 to 2 b-2.2 to 2.4 c-3 to 3.5 d-1.008 vii-For a 1cm gap in air at 760 mm pressure and 20 °C temperature the breakdown voltage is: a- 24kV b-30.3kV c-22.92kV d-40kV

iv-ionization coefficients a, y are function of a-applied voltage b-pressure and temperature c-electric field d-ratio of electric field to pressure v-The relation between breakdown strength and gap distance in liquid dielectric is V₁: a-K/d b-Kd c-Kd-n d-(Kid + K₂) vi-Dielectric constant of mineral oils is about a- 1.5 to 2 b-2.2 to 2.4 c-3 to 3.5 d-1.008 vii-For a 1cm gap in air at 760 mm pressure and 20 °C temperature the breakdown voltage is: a- 24kV b-30.3kV c-22.92kV d-40kV

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The difference between insulator and semiconductor is a. wider gap between valence and conduction band b. the number of free electrons c. the atomic structure d. all of the above
B01.2 QUESTIONS ON THIS CHAPTER C a رها The conductivity of a pure semiconductor is due to: al electrons. 2 □ 3 04 □5 al 02 3 04 5 A pure semiconductor is a good conductor when the temperature is: □ 2 □3 4 5 AP type semiconductor is obtained by adding impurities such as: al LESSON BOI: INTRODUCTION TO SEMICONDUCTORS 2 holes positive ions of the N regions and electrons electrons and holes positive ions of the P regions and holes □ 3 04 5 very high very low ol □ 2 □ 3 4 □5 absolute zero when ranging between 0 and 25 °K it is not affected by temperature An N type semiconductor is obtained by adding impurities such as: those belonging to group III of the periodic table of the elements al phosphorus only those belonging to group V of the periodic table of the elements those belonging to the group III of the periodic table of the elements antimony only gallium only boron in the proportion of 25 %, and arsenic as 75 % boron only aluminum and antimony together at 50% those belonging to group V…
An 18-gauge copper wire with a diameter of 1-mm carries a constant current of 1-A. The charge concentration in the wire is 8.5 x 1028 per cubic meter. Determine the electric field in mN/C. Use q = 1.602 x 10-19 and resistivity equal to 1.72x10-8 ohm-m.
b. A piece of pencil lead is connected in series with an ammeter and a power supply. The power supply is turned on. After a few minutes, although the potential difference across the pencil lead does not change, the current in the circuit increases significantly. Explain why the current increases. c. Electric fields are caused by both point charges and by parallel plates with a potential difference across them. Describe the difference between the electric field caused by a point charge and the electric field between parallel plates. Your answer should include a diagram of each type of field and reference to electric field strength. Question 2
Determine the current 1, 12, 13 in mA and the voltage across R1 for the network shown in the figure if E=30 V. Assume diode to be silicon. D I, 3.3 kn R2 13 D2 R1 5.6 kN
Use Kirchhoff's law method Indicates the conduction status of the diode The result is the table of current and voltage values for each element Incorporates the diode conduction voltage if applicable 7) R1 - IK E1 R2 lov (+ D1 esi D2@s
An 18-gauge copper wire with a diameter of 1-mm carries a constant current of 1-A. The charge concentration in the wire is 8.5 x 1028 per cubic meter. Determine the resistance, in ohms, of a 77-m wire in milli-ohm. Use resistivity equal to 1.72x10-8 ohm-m.
2. When a current of 1A flows through a wire, the drift velocity of the electrons is 0.9 mm/s. What will be the drift velocity of the electrons when a 2A current flows through another wire of the same material having double the length and double the area of cross section and same temperature.
İNGİLİZCE TÜRKÇE RUSÇA In a semiconductor crystal, atoms are held together as follows: Please choose one: a. gravitational forces b. covalent bonds C. interaction of valence electrons D. answers A., B. and C. 92/5000 13:30 30.04.2021
A diode network is given in Figure-1. a) Explain the tasks of the diodes (parallel and serial) and resistor in the network b) Calculate I and V. . 4Ic (mA) 30 µA +20 V 25 μΑ Si 5 20 μΑ 4 15 μΑ Ge Si 3 10 µA B 5 μΑ Ig = 0 µA 2.2 k2 10 15 20 VCE 4V Figure-1 Figure-2 2.
Question 10 Find the resistance in micro-ohms at 20 °C of an annealed copper bus bar 4.8 m in length and 0.4 cm by 3.6 cm in rectangular cross section. The resistivity of annealed copper is 1.72 x 10-8 Q-m at 20 °C. Your Answer:
D3 D1 V1 sine R1 1 kHz D2 D4 Given: • V1 = 5.9 Vrms • R1 = 7 kOhm • Diode voltage = 0.9 V What is the maximum voltage across resistor R1 (in V)?