Ituation 3 - The portable camping tool shown in the Figure AP-4.7 is to support weight W at a variable distance x from D. In this problem, L1 = 540 mm, hi = 240 mm, hz = 120 mm.

Q: A Pully drive system used in washing machine is designed based on flat belt as in Figure.1/a. The…

A: Given Data The tension in the pulley is:To=140 N The coefficients of friction is:μ=0.25 The lap…

Q: For the simple truss in figure QI below, 9 KN 6 kN 3m 3 m 3m 3 m 5 m Figure Ql: Simple truss…

A:

Q: olved force P so the box will rest in the position as shown in figure P-310. Assume the inclined pl…

A: Given Data : W=300 lb θ=600

Q: Find the magnitude of the compressive force acting on the gate shown in the figure and then…

A: Given:

Q: 5.5-8 A freight-car axle AB is loaded approximately as shown in the figure, with the forces P…

A:

Q: A 2 hp, 2500 rpm electric motor drives a machine through a flat belt. The driven shaft speed…

A:

Q: The rigid arm of negligible weight shown in the figure supports a load of F = 852 N. The chains are…

A: Given data: F=852 Nx1=5 mx2=4 my=7 mz=5 m Need to determine the Magnitude of the force in FBE.

Q: A load weighing P kN as with AB, AC and AD cables such as are carried. Points A and B are x-axis, C…

A:

Q: H a P P P 6 panels at 10 m = 60 m Figure Q4(a)

A:

Q: Please solve with step and explaining, thank u

A: Given: A four link mechanism is shown in the figure. All the dimensions of the links are given and…

Q: Question 1: A railway crossing boom gate, as shown in Figure 1, consists of three parts: • 60 kg arm…

A:

Q: A 125ON sphere in figure is supported by the pull P and a 83ON weight passing over a frictionless…

A:

Q: Find the reactions at contact points A, B, and C, given: F = 85 lbs, L, = 0.8 ft, L2 = 1.6 ft, L3 =…

A:

Q: Find the equivalent torsional spring constant (up to two decimal points) of the system shown in the…

A:

Q: ///////// with spring constants c 3

A: For this problem we are going to use stiffness matrix method. We have,  [K] [D] = [F]   where, K =…

Q: on plane of L3 Co, 0.0)

A:

Q: A 1,000-N uniform boom at - 62.5" to the horizontal is supported by a cable at an angle of weight w=…

A: Given data is

Q: 3/14 To facilitate shifting the position of a lifting hook when it is not under load, the sliding…

A:

Q: For the figure shown if P= 750 N required for the system to be in equillibruim determine the force Q…

A:

Q: 1. In lecture I focused on a horizontal mass-spring system so we could ignore gravity, but in…

A: Given: To find: Equation for the mass Equation for y' Force when y'=0 Total energy y and y'…

Q: Q2/ Hydraulic cylinder is used to lift cars weighing 75 kN for 550 mm in 6 sec. The ratio of…

A: Given Data The weight of the car is:W=75kN The distanc of lift is:h2=550 mm=0.55m The time is:t=6 s…

Q: (MO13) 3. A four bar mechanism consists of L1=40mm, L2=33mm and L3=120mm. Find the range of values…

A: Given data as per question L1=40 mmL2=33 mmL3=120 mm

Q: The block shown in the figure below is acted on by its weight, W = 1300 Lbs, a horizontal force H =…

A:

Q: K2 ww he spring shown above, 00 N/mm, k2-200N/mm, k3%3D100N/mm, P-5 he global stiffness matrix…

A:

Q: A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the…

A: Given Length of the ladder = 10 m Weight of the ladder = 350 N Ladder angle = 30o Weight of the…

Q: 8. Refer to figure 9. Given the following information: angles 0r= 20°, 02= 30°, 03= 41°, a 200 N…

A:

Q: A landing gear mechanism is shown in the accompanying figure. You may assume that it is in static…

A: Solution: Given Data: W=225 lb   To Find: (a) The force in link AB. (b) The magnitude of the pin…

Q: Q1: A: Draw a Free Body Diagram of the bars AD and BC shown in the figure. Assume all hinges to be…

A: Solution:

Q: B Consider the system given in the figure. The spring may sustain compressive as well as tensile…

A: Given:To find:Derive the equation of motion.

Q: The single degree of freedom system shown in Figure 3 is at its undeformed position. The SDOF system…

A:

Q: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a…

A:

Q: ing and a rope that runs over a stationary pulley at point D (neglect the dimensions of the pulley).…

A:

Q: Part D -A tractor shovel The tractor shovel shown (Figure 4) carries a 550 kg load that has its…

A:

Q: Need help on all questions. Please include all units, steps to the problem and information such as…

A:

Q: er the given lengths as shown, the mechanism is

A:

Q: Find the value of the input torque on the crank-shaft mechanism in following Figure. The centers of…

A: Itis asked to carry out dynamics analysis of the mechanics given below

Q: spring system given in Figure Create the element matrices as well as the global stiffness and force…

A:

Q: igure Q5a shows a truss structure in static equilibrium that is simply supported at A and C.…

A: Draw the free body diagram for the above problem as follows.

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.