Its an aswer but i cant read it. please tpe it

Q: | نقطتان )2( -- drink lot of water because l .am thirsty must have to

A: I have to drink a lot of water because I am thirsty  here we need to use have to instead of must

Q: A direction cosine is: O The cosine of the angle between a vector and a particular coordinate axis.…

A:

Q: Some homes that use baseboard heating use copper tubing. Hot water runs through and heats the copper…

A: Mass of the copper tube,(m)=540 g. Initial temperature,(T1)=15.01oC Final temperature,(T2)=25.48oC…

Q: In 1960 the German company Krupp Steel Works constructed the spherical pressure chamber for the deep…

A: Let the  volume of sphere be V. The density of sea water is 1025 kg/m3 and density of air is 1.2…

Q: Give the name of the following graphic symbols or Draw the graphic symbol according to the following…

A:

Q: Which et h

A: introduction: Forging is a manufacturing technique that involves pounding, pressing, or rolling…

Q: >»Which would you expect to be stronger; a polymer with a high molecular weight or one with a low…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked…

Q: i cant read this, can you rewrite

A:

Q: Given the multiview projection of the solid, draw the isometric view.

A: Given:To find:Draw the isometric view.

Q: Q4/ Using three different ways, compute the the moment of the force 400 N about O? 400 N 100 mm 60°…

A: Bending Moment(BM):- Bending happens whenever a point in time or couple acts about just a…

Q: The hand writing is not very clear :(

A: Basically the miller indices are the set of numbers which define the particular plane in the crystal…

Q: Give the name of the following graphic symbols. M) (a) (b) (c)

A: Given: Name the graphical symbols.

Q: The given system of forces is, F2 F3 m

A:

Q: . An +A22 + A33

A: For solution refer below images.

Q: A power plant turbine releases its discharge into a condenser operating at 20C at 100% saturated…

A: It is given that:condenser temperature is 20°C. Steam enters condenser as 100% saturated vapor.Mass…

Q: a powerp u, a process design id wastes (MSW) per hour. In an industrial boiler, MSW is burned to…

A: To given thatH1=104.93Kj/kgH2=2675.53kJ/kgH3=2942.73kJ/kgH4=3324.63kJ/kg

Q: gedem +x) 1+2) Circle the letter corresponding to the view on the right that shows the result of…

A: First, rotates the object along the y-axis in an anticlockwise direction then again rotates along…

Q: THIS IS AN INSTITUTIONAL EXAM. P NOT FOR SCADING ON ANE TUTORIAL BITE SUCH AS, BUT NOTUMITED TO…

A: According to the question data A loading structure is given  compressive member area=400mm2 Tensile…

Q: E pelermine what Type of Alter shownn The figer batew fake .R=2k Conseder The S=JW L=2H and G2Mi

A:

Q: A mobile crane has a 25 ft long boom (OA). The center of gravity (G1) of the boom is located at its…

A: Draw the F.B.D of the truck.

Q: For an undamped vibratory system, the velocity leads the displacement by rt/2 rad. Select one: O…

A: False

Q: This problem set deals with the problem of non-constant acceleration. Two researchers from Fly By…

A: Given: To find: Write all equations Construct least squares problem Construct system of normal…

Q: Ә Show ox (Txx) + 1 (Tyx) = uT²и. ду

A:

Q: Single pipe with pump) Without the pump shown in the figure below it is determined that the flowrate…

A: The power absorbed by the pump can be calculated using the formula give below as- P=ρgQhf where, P…

Q: A business equipment room has 1000 watts of lighting and some small motors with a total output of 10…

A:

Q: Identify the drawings as isometric, trimetric, oblque or perspective. A. B

A: Isometric projection is a technique used in technical and engineering drawings to visually…

Q: Circle the letter corresponding to the view on the right that shows the result of rotating the…

A: (1) Find Rotate the object (1) about the z-axis and then about the x-axis.

Q: Completely solve and box the final answer. Please show the units to show the unit cancellations.…

A:

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: Cranes serve the purpose of lifting, transporting and lowering the load so heavy frameworks are used…

A:

Q: Please explain how the moment of FAB and FAD were calculated in this picture. For example, I dont…

A:

Q: B ) its a solve question plrase type it . i cant read handwriting

A: step 4Now we will apply material balance for salt on second tankSalt input rate-Salt output rate =…

Q: A very large wind turbine with a rotor diameter of 200 m can generate a maximum of 14 MW output…

A: Given:The rotor diameter of the turbine, The maximum power output, The pressure of the hydrogen,

Q: dH VdP = dS T т (1) show that equation (1) leads to equation (2). please don't use any other…

A: Given DatadH=Tds+VdPto ProvedHdPT=V1-βT

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: The solid rod shown has a radius R. Given that: P = 2 kN R = 25 mm %3D %3D X = 200 mm y1 = 125 mm y2…

A:

Q: 2. Small packages traveling on the conveyor belt fall off into a 1-m-long loading car. If the…

A: Given data: In the figure given vc=2 m/s and in the below problem vc=3 m/s both are different so I…

Q: Question: Sketch the greaphs of T and T2

A: The given question is not clear about which topic. Assumed, the graphs required related to…

Q: Two geological field teams are working in a remote area. A global postioning system (GPS) tracker at…

A:

Q: alalale the vorFidene by an going frem AR. slake A oc for each t ABE b) ABG O ACdirectly

A: Data given - A P-V graph  Need to calculate by path  a)  ADC  b) ABC  c) AC

Q: What is the shortcut key for "Find and ?Replace" dialog box + Ctrl + Shift + FO Ctrl + RO Ctrl + FO…

A: Correct answer: Ctrl + H

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.