Item#3 The oil tank for the hydraulic system of figure below is air-pressurized at 10psig. The inlet line to the pump is 10 ft below the oil level while point 3 is 2ft below pump inlet. The pump flow-rate is 30 gpm and has a power equal to0.5HP. Find the pressure at station 3if there is a 28ft head loss between station 1 and 3. OIL LEVEL SG=0.9 1.5-IN- INSIDE DIAMETER 10 FT MPUMP STRAINER ELECTRIC MOTOR

Item#3 The oil tank for the hydraulic system of figure below is air-pressurized at 10psig. The inlet line to the pump is 10 ft below the oil level while point 3 is 2ft below pump inlet. The pump flow-rate is 30 gpm and has a power equal to0.5HP. Find the pressure at station 3if there is a 28ft head loss between station 1 and 3. OIL LEVEL SG=0.9 1.5-IN- INSIDE DIAMETER 10 FT MPUMP STRAINER ELECTRIC MOTOR

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A turbine is used to produce 2700 hp by expanding the water between points 1 and 2. Water flow rate, static pressures and pipe diameters are given. Calculate the power lost in between point one and two. Note that the static pressure at point 2 is given in vacuum. (SGH =13.6) P1 = 60 psi Q = 150 ft³/s D = 3 ft Section (1) Turbine 10 ft P2 10-in. Hg %3D vacuum D2 = 4 ft Section (2)
A manufacturing company uses a 100 bar hydraulic power system which supplies 10 liter/minute of oilflow. The shaft speed is 1500 RPM and the nominal displacement is 8 cm3/revolution. The theoreticaldrive torque is 11.4 Nm. If the electric motor driving the pump has an efficiency of 95%,a. Name in detail all 27 hydraulic power components as illustrated in the above figure.b. Calculate the volumetric efficiency, the fluid and shaft power, the overall efficiency of the pump.
Q1. The figure below shows a hot water tank, with a pumping arrangement to continuously circulate water in a loop. Plastic pipes used, with six bends and two gate valves, as shown. Given that the water is flowing at an average velocity of 2.5 m/s, calculate the required power input for the pump. Given: The density and viscosity of water at 60°C are p = 983.3 kg/m', u = 0.467x103 kg/m-s. Plastic pipes are smooth, and thus their roughness is very close to zero, ɛ = 0. The loss coefficient is K1 = 0.9 for a threaded 90° smooth bend and K1 = 0.2 for a fully open gate valve. Assume 70% pump efficiency. 1.2 cm Hot Water tank 40 m
A pumping system has the following characteristics, f=0.015 length of thepipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipeis cast iron, and the system curve is:Hp= 34+ 5.47Q2Knowing that the system curve and the pump curve intersect at 12 cfsa. Determine Operation headb. Determine dischargec. Plot the system curve
Subject: Fluid Machineries
4
Q1) Figure Ql shows piping system with pump to drive the oil upward from A (P=PA kPa) to B (P=180 kPa) at a mass flow rate of 3 kg/s. Determine type of flow and calculate required pump power. Given data: oil density and viscosity are 891 kg/m³ and 0.29 N.s/m² respectively. Use Hagen Poiseulli equation for loss: he128µQL/(xpgD“) and Power=Qpghr; Triangle geometry: a²=b²+c² Dripe = 3 mm 15 m Pump 20 m Figure O1
Q3
Problem-3: A centrifugal pump lifts water against a static head Az = EN m. The pipe setup has a constant diameter of 0.08 m, major losses in the suction side h, = EN3 m and in the discharge side hLD is 3 m. The pump impeller has a diameter of 0.15 m, exit width of 0.015 m, exit blade angle of 22° and speed of N = 20EN rpm. The hydraulic efficiency is 0.85. If the flow at the entrance is radial, find the discharge, pump head, atmospheric pressure Pat, Vapor pressure P, and maximum allowable height of the pump from the feeding tank water surface elevation if the pump is operating under T 25 °C at altitude H= 20EN m. %3D 0, = NPSHR/Hp =1.21×10³N = (P EN=62 Is-mx at-abs-P,)/Y-hLsT -0H, Pa-abs /Y = 10.33(1– 2.256x10-H)56 P,ly = e14.29-3985(T+233.4))
Show complete solution and formulas used. Show the schematic diagram too. Calculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min water from a closed tank, where the pressure (above the water level) is p = 40kPa. The equivalent length of the smoothened concrete pipe on the suction side is 12m while the suction flange of the pump is 8m below the water level. The vapour pressure at the given water temperature is 2.8kPa. The required net positive suction head is NPSHr = 3.2m.
5
Problem 3