It is the ratio of the units of electricity generated per year to the capacity of the plant installed in the station ratio of the duration during which the plant is in actual service to the total duration of the period of time considered ratio of the average load to the peak load during a certain prescribed period ratio of the average load on a machine or equipment to the rating of the machine or equipment, for a certain period of time considered Ratio of maximum demand of the plant to the rated capacity of the plant

It is the ratio of the units of electricity generated per year to the capacity of the plant installed in the station ratio of the duration during which the plant is in actual service to the total duration of the period of time considered ratio of the average load to the peak load during a certain prescribed period ratio of the average load on a machine or equipment to the rating of the machine or equipment, for a certain period of time considered Ratio of maximum demand of the plant to the rated capacity of the plant

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What are the methods for voltage regulation in a power distribution system, and how are they implemented?
Problem 1 Power System Standards and Related Assume a standard duplex outlet is wired correctly and meets the National Electric Code (U.S.) The load is operating correctly with no defects in operation or internal wiring. Answer the following: Write a time domain, rms phasor, and peak phasor (a) expressions for the voltage between: (i) Short slot with respect to the long slot (ii) Short slot with respect to the round hole (iii) Long slot with respect to the round hole (b ) (NEUTRAL WIRE, HOT WIRE, GROUND WIRE) of a power distribution system and this wire is color coded (GREEN OR BARE, BLACK OR RED, WHITE) and would connect to the (ROUND HOLE, SHORT SLOT, LONG SLOT) of a standard duplex receptacle. The National Electric Code specifies that a circuit breaker or fuse must always be located in the (c) (10% of the current in the black wire, 10% of the current in the white wire, Zero, 90% of the current in the black wire, 90% if the current in the white wire). The current in the ground…
Sub:Distribution
Sub:electrical distribution
The maximum demand of a power station is 110 MW. It generates 105 x 10 units during the day. The station has three units of 40 MW and another unit of 40 MW as spare. The running hours of the unit are as follows. The first unit of 40 MW runs for 24 hours. Another unit of 40 MW runs for 14 hours. A third unit of 40 MW runs for 4 hours. So Find (1) daily load factor (2) plant capacity factor (3) utilization factor and (4) plant use factor.
Explain how electricty power is generated and tramnsimitted to customer unit. Show The single line diagram of a typical distribution system. Also Explain different methods of electricity distribution and the equipment used for different methods of electrical distribution.
2. a) Explain the terms load factor and diversity factor. b) Discuss the advantages of interconnected grid system. c) A generating station is to supply four regions of load whose peak loads are 10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Calculate: (i) the maximum demand on the station, (ii) annual energy supplied by the station and (iii) suggest the installed capacity and the number of units.
1: Answer only one of the following: A- What are the advantages of a diesel power station? B- Several points should be taken into account in the selection of the site for the Nuclear power station. State these points.
How do power system operators manage and balance electricity supply and demand in real-time?
Draw the schematic arrangement of diesel power plant
Explore the challenges and solutions related to power quality in electrical systems. How do issues like voltage sags, surges, and harmonics affect sensitive equipment, and what measures can be taken to mitigate them?
e) Find the total reactive power in the sound system without using the voltages across loads.Mention the unit. f) Find the apparent power of the system. Mention the unit.