It is required to design the common-source amplifier below to provide a gain of -20 V/V. It is given that gm3 = 3.63 mA/V, (W/L)1 = 50, (W/L)2 = 60, (W/L)3 = 110, VAn = 10 V, VAp = 5 V, and.µA/V2 %3D %3D %3D %3D %3D %3D (a) Find the transconductance parameter gm3- (b) Find the DC bias current Ip. (c) Find the reference current IREF. Hint: A, = -9m3 (ro2 || ro3) %3D Im = 21th Cox () ID %3! VDD Q2 Q1 Ip IREF Q3 Insert the DC bias current, Ip, in mA below:

It is required to design the common-source amplifier below to provide a gain of -20 V/V. It is given that gm3 = 3.63 mA/V, (W/L)1 = 50, (W/L)2 = 60, (W/L)3 = 110, VAn = 10 V, VAp = 5 V, and.µA/V2 %3D %3D %3D %3D %3D %3D (a) Find the transconductance parameter gm3- (b) Find the DC bias current Ip. (c) Find the reference current IREF. Hint: A, = -9m3 (ro2 || ro3) %3D Im = 21th Cox () ID %3! VDD Q2 Q1 Ip IREF Q3 Insert the DC bias current, Ip, in mA below:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What are circuits can used to design Class B amplifier ? explain the important features ? for each
Basic Electronics
Q1)For the Zener regulator circuit shown in figure ,lf Vi take the following values 10V, 15V, 20V and the circuit has the following properties (VZ=12V,R=1KQ,RL=6KQ and PZmax.=120mW)Find the following Is=IR, .IZ , IL, and VL for each input values R VL PzM
The circuit in the visual containing a non-linear element will be analyzed with the Small Signal Analysis method and the VR2 (t) voltage will be calculated. For this purpose, linearize the non-linear element at the operating point.
Q-2: The Si transistor circuit of the figure shown, find the emitter resistor (RE) that would bias for operating about VcEo = 5V. Let ICEO = 0, B-80, Rg = 220KN, RC = 2KN and Vec = 12V, where Ic # Ig. %3D Vec Re RF Ce RL Rs Vs RE
At any point on the characteristics the product of VCE and IC must be equal to 300 mW. If we choose IC to be the maximum value of 50 mA and substitute into the relationship above, we obtain VCE=? VCEIC = 300 mW a. 6 V b. 5 V c. 10 V d. 8 V
(d) An instrumentation amplifier is used when the application signal is very low. For the circuit shown in Figure Q2(d), calculate the applied input vin of the circuit to get the output of 5V at vo. Let Rr=360k 2 and R₁ = 12k 52. Rf www R1 Vec www Vo -Vec Figure Q2(d) (e) Illustrates instrumentation system for temperature measurement with the help of block diagram. Vin uA741
2. For the given circuit, 6 = 100 and VBe = 0.7 V, determine IB, VCe, VB, Vc, Ve %3D vcc 18V VCC R1 47k2 R4 2k2 2 R3 1 2kQ BJT_NPN_VIRTUAL 3 R2 R5 10k2 1kQ 4.
Q. 6, Find the omorgy of -2/t/ 4 the signal gven below: x (4)=e E Josle. ans:
In the circuit given in the figure VT = 25mV, | VBE | = 0.7V, R1 = 515.22Kohm, R2 = 10.89Kohm, R3 = 2.41Kohm, R4 = 1.03Kohm, VCC = 12.00V, VEE = 2.00V, VA = 12.51V, Beta Since = 107.00, Rs = 23.19ohm, Ry = 8.18Kohm, calculate the IC current, Ri, R0 and voltage gain according to the Source (V0 / V1) by making full analysis.
C6 Shown in Figure C6 is a common emitter amplifier. Follow the specification below and calculate the value of R1 given the information provided. RC Voe vce Vbe vcc = 10 V, VE=1 v, VBE = 0.7 V, IC = 2 mA, B = 100, I(R1) = 10XIB, V(RC) = VCE = 4.5 v RI RL Ve Vbb Figure C6 Common Emitter amplifier with Potentiometer Bias A. No answers below are correct B. R1 = 13.5 ko C. R1 = 21.6 kO D. R1 = 8.5 kn
I need the answer as soon as possible