It is known that the different equations of a system are as follows: 3y[n - 2] - 2y[n - 1] - 2y[n] = x[n] + 2x[n - 2] a) Determine the Transfer function from the difference equation above (use the Z transformation). b) Determine the polish and zore at point a c) Draw the positions of the poles and zores at point b in the diagram

It is known that the different equations of a system are as follows: 3y[n - 2] - 2y[n - 1] - 2y[n] = x[n] + 2x[n - 2] a) Determine the Transfer function from the difference equation above (use the Z transformation). b) Determine the polish and zore at point a c) Draw the positions of the poles and zores at point b in the diagram

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

R₁ R₂ VDD M₁ CG Vss = 0 V RD Cs Rs Figure 1 Vout Vin
Write down at least three reasons which cause difference between R1 (R2) and R = Vmes/imes values in the below table?
i need ans very fast
2. Solve for the following: a. Is b. I L c.I z Rs = 120 N Vz = 12 V PZM = 1 W Vin = 18 V R = 400 N %3D +
Find the equivaleut resistance between A andt AAAAA AMA AAMA
VDD- 10 Velt 106 ID2 I07 Assume the following: (a) M1 and M2 are matched (b) = 0 for all MOSFETS (c) L identical for all FETS. (d) ID2 = 50 µA. (e) W1=W2=W3=W6=W8 (f) W4=W5=2 x W2 (g) W7=3 x W8 (h) Except for W/L ratios establishëd by the photolithography design, the fabrication process is the same for all FETS. Pay attention to sign convéntions! Provide values for: ID3 ID4 ID7 ID5 = drain circuit for M5! (Trick question. Careful-look at the
Calcule V2, aplicando análisis de nodos.
1. Determine the sensitivity [mV/ C] of the measured data for the thermocouple. The output and input are the measured electromotive force [mV] and temperature [°C), respectively. mV 4.37 8.74 13.11 17.48 °C 250 500 750 1000
A Dashboard Events E My Courses This course Find i0 by using current division method. R1 = 20 Q R2 = 12 Q R3 = 16 Q R4 = 24 Q Rs = 10 Q R2 R3 io 10 A( R1 Rs R4 Select one: here to search TI78 EENG250 Midterm . Ở Settings
Q1: For the circuits shown in figures. If the temperature has changed from 25°C to 65°C. find AIc. Ic=1.5mA at 25°C. Vcc +20v 25°C 65°C 47k 33.9k 55 70 Ico InA 16nA 12knS VBE 0.6 0.5 S1.2k
Dopant density (cm-³) 1021 1020 1019 1018 1017 1016 10¹5 1014 1013 10¹2, 10-4 10-3 10-¹ 10⁰ 10¹ 10² 10³ 104 Resistivity (ohm-cm) FIGURE 2-8 Conversion between resistivity and dopant density of silicon at room temperature. (After [3].) N type 10-2 P type EXAMPLE 2-3 Temperature Dependence of Resistance a. What is the resistivity, p, of silicon doped with 10¹7cm-3 of arsenic? b. What is the resistance, R, of a piece of this silicon material 1 um long and 0.1 μm² in cross-sectional area? c. By what factor will R increase (or decrease) from T = 300 K to T = 400 K? d. What As concentration should one choose if she wishes to minimize the change in (c)?
-2€ Cost 2 (8) (Sinzt + Coszt ) -3€ @ 2"(2Gsst-35sin5t) 2t 3 L £(6) ...