ISMB 450 is used as a propped cantilever beam of span 12 m. Assuming oy = 250 MPa determine the factored uniformly distributed load q, the beam can carry including self weight, if the load is to be applied over the entire span. The properties of ISMB 450 are as follows: Weight/metre area of cross-section width of flange thickness of flange : 72.4 kg : 9227 mm² : 150 mm : 17.4 mm I 3.039 x 108 mm4 I... = 8.34 x 106 mm4 yy

ISMB 450 is used as a propped cantilever beam of span 12 m. Assuming oy = 250 MPa determine the factored uniformly distributed load q, the beam can carry including self weight, if the load is to be applied over the entire span. The properties of ISMB 450 are as follows: Weight/metre area of cross-section width of flange thickness of flange : 72.4 kg : 9227 mm² : 150 mm : 17.4 mm I 3.039 x 108 mm4 I... = 8.34 x 106 mm4 yy

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2. Replace the force system acting on the frame by an equivalent resultant force and specify where the resultant's line of action intersects member AB, measured from A. * 50 - 150 lb 100 - 200 lb A B 30 200 - 300 lb 2 ft -2 ft 2 ft 300 - 400 lb 2 ft 300 - 400 lb 2 ft 1 Add file 2.
An over hanging beam ABC of length 10 m (including over hang portion) is shown in the figure below. The ratio of ILD ordinates at C to ILD ordinates at B for the shear force at B is A B 7 m 3 m-
Two simply supported beam A and B are under same udl Loading. The span of A is double of span B. The correct statement is 1. 2₁ 3. 4. Deflection of A = 2x Deflection of B Deflection of A 4 x Deflection of B Deflection of A = 8 x Deflection of B Deflection of A =16 × Deflection of B
E=60 KN A=40 KN
A simply supported girder spans 10 m. It carries two beams each at 3.5 m from the supports. The concentrated load from each beam is 70 kN
A steel column carries an axial load of 808 kN and a moment of 76 kN-m at the top and moment at the bottom which is only70% of the moment at the top. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties: A = 13080 mm2 rx = 109 mm ry = 94 mm Sx = 1200 x 103 mm3 K = 1.0 L= 3.6 m E = 200,000 Mpa Fy = 248 Mpa Use NSCP specification for compressive stress and Fb =148 Mpa. Determine the Allowable Compressive Stress.
1. From the tabulation below determine if the column is safe to carry axial & bending load Yield stress of structural steel is 248 MPa. Modulus of elasticity is 200,000 MPa Service Load: Pl= Pd= assume K=1.0 Designation W8 x 28 W8 x 24 W8 x 21 W8 x 18 60 kN 100 KN Ag (mm2) 5323 4568 3974 2865 Weight/m d (depth) 42 bending moment Mux - Muy = 16 kN.m (LRFD load combination) bending moment Mx=My=12 kN.m (ASD load combination) L=3.6m flange Web 36 31 27 204.72 201.42 210.31 206.78 mm. width bf 165.99 164.97 133.86 133.35 thickness tf 11.81 10.16 10.16 8.38 thickness tw 7.24 6.22 6.35 5.84 Elastic Properties mm 4 mm 3 Ix x 106 Sxx 103 41 34 31 26 398 342 298 249 mm. rx 87.63 86.87 88.65 87.12 mm 4 lyx 106 9 8 4 3 mm 3 Sy x 106 109 92 61 50 mm ry 41.15 40.89 32 31.24 Plastic properties mm 3 Zx x 103 446 380 334 279 mm 3 Zy x 103 166 140 93 76 h=d-2k h 155.58 155.58 168.28 168.28
Steel column pinned at both ends has a modulus of elasticity E = 2 x 105 N/mm², moment of inertia I = 90000 mm4, L = 1.75 m, value of Euler's critical load will be
Thankyou.... please solve