ISMB 100 (r = 40 mm, r = 10 mm) has been used as a column in a industrial shed. Along the minoraxis, the the column has restraints in the form of purlins at 1.0 m intervals. Effective length factoralong major and minor axes are 1.2 and 1.0, respectively. If the slenderness ratio is restricted to120, the maximum column height will be

Given- ISMB 100, Effective length factor along major and minor axes are 1.2 and 1.0, respectively.…

ISMB 100 (r = 40 mm,r, = 10 mm) has been used as a column in a industrial shed. Along the minor axis, the the column has restraints in the form of purlins at 1.0 m intervals. Effective length facto along major and minor axes are 1.2 and 1.0, respectively. If the slenderness ratio is restricted to 120 the maximum column height will be

ISMB 100 (r = 40 mm,r, = 10 mm) has been used as a column in a industrial shed. Along the minor axis, the the column has restraints in the form of purlins at 1.0 m intervals. Effective length facto along major and minor axes are 1.2 and 1.0, respectively. If the slenderness ratio is restricted to 120 the maximum column height will be

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please solve part 4.3
A steel column carries an axial load of 819 kN and a moment of 63 kN-m at the top and moment at the bottom which is only70% of the moment at the top. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties: A = 13172 mm2 rx is 109 mm ry = 94 mm Sx = 1200 x 103 mm3 K = 1.0 L= 3.6 m E = 200,000 Mpa Fy = 248 Mpa Use NSCP specification for compressive stress and Fb =148 Mpa. Determine the Compressive Stress if Axial load only existed.
3) The simply supported beam with the cross-section as shown supports a total uniformly distributed load of 4P and 2P and concentrated load P as shown in the figure. Determine the maximum allowable value of P if the allowable flexural stresses are limited to 35 MPa in tension and 150 MPa in compression respectively. 1m P B 1m IC 4P 3m D 2P 1m DE U 175 200 (Dimensions in mm)
The rigid frame shown in Figure is unbraced. The members are oriented so that bending is about the strong axis. Support conditions in the direction perpendicular to the plane of the frame are such that Ky = 1.0. The beams are W18 x 50, and the columns are W12 x 72. A992 steel is used. The axial compressive dead load is 50 kips, and the axial compressive live load is 150 kips. a. Determine the axial compressive design strength of column AB. Use the stiffness reduction factor if applicable. b. Determine the allowable axial compressive strength of column AB. Use the stiffness reduction factor if applicable.
please solve question 4.2, quickly please
Assume that all members are pin connected and P = 5 kN. (Figure 1) Figure 3 m -3 m3 m3 m+ 44 Determine the force in member AB of the truss and indicate whether the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FAB= Part B Submit Request Answer FAH Submit ▾ Part C Ti HA Determine the force in member AH of the truss and indicate whether the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FBC= Value Submit Value PA 6 → IB'? Request Answer E'? Determine the force in member BC of the truss and indicate whether the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case…
please solve part 4.1
9. A steel portal frame has dimensions, plastic moment capacities and applied loads as shown in the figure. The vertical load is always twice of the horizontal load. The collapse load P required for the development of a beam mechanism is P A B Mp K 2P 2Mp L с Mp D L
Please explain the reasons
Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; = 1990 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA= 250 kip-ft, P= 14 kips, LAB = 4.1 ft, LBc = 6.2 ft. MA LAB LBC Answer: in. (a) VA- in. (b) VB - 4. Submi Attempts: 0 of 1 used Save for Later
M-0 relationship for a simply supported beam shown below is given by M A 1 0 M OO
SHOW COMPLETE FBD