Is Refrigerator an open loop or closed loop system? Write the reason for your answer. For the refrigerator system, draw a simple block diagram with the name of input, output and control system used.

Q: Find the impulse-response function (the two-variable one) of each system described in Question 1,…

A: In Q. 1, the deterministic, linear, continuous-time, and analog systems are c yt=∫t-1t+1uτdτ,d…

Q: Microwave Oven an open loop or closed loop system?

A: Open Loop System- A control system in which the input of the system does not depends on the output…

Q: Draw a simple block diagram of 'Open-Loop Control System' and 'Closed-Loop Control System' Not…

A: CS - control system

Q: A system has a closed loop transfer function: K(s+3) s4 +7s³ +14s² + (8 +K)s +3K Using the…

A: here we have to find the range of k for system stability.

Q: 3. An aircraft's attitude varies in roll, pitch, and yaw as defined in Figure P1.2. Draw a…

A: solution given That roll, aircraft's altitude varies in yaw pitch and Block diagram For closed…

Q: Identify the system which has low stability. a. None of the above b. Open loop and Closed loop…

A: Consider the open loop control system: In this the control system depends only on the input and is…

Q: Give a real time example of an open loop system and explain with neat diagram the operation of it.…

A: an open-loop system is a type of control system in which the output of the system depends on the…

Q: Part 2: Analysis and selection of the Wind Turbine. The team decides at install a 30 MW wind farm.…

A: 1: Analysis and selection of the Wind Turbine.The team decides to install a 30 MW wind farm. The…

Q: Write any two (different) examples of controllers used in closed loop systems. Your examples of…

A: the control system that has a feedback loop is known as feedback control systems. In closed loop…

Q: Experiment: We apply a step voltage u(t) = 5u,(t) and we observe the output voltage y(t) on an…

A: The given circuit is shown below: Ctp=8.65 VC∞=5 Vut=5ustts=5 s

Q: he transfer function of a position control system is given by: etermine: a) Tp C(s) 1500 R(s) 2s²…

A: For the given transfer function Find  a) peak time b) percentage overshoot c) Rise time d) settling…

Q: Simplify the following block diagram and determine the overall transfer function of the system Y(s)/…

A:

Q: While discussing armature testing: Technician A says to test for shorts, place the ohmmeter leads on…

A:

Q: () Discuss the cascade control scheme for a heat exchanger system with a neat diagram. (i) List down…

A:

Q: 1. Give a real time example of an open loop system and explain with neat diagram the operation of…

A:

Q: usal. (a) h[n] = (1/2)"u[n] (b) h[n] = (1/2)"u[n – 1] (c) h[n] = (1/2)m %3D %3D

A:

Q: questions, thank you. Calculate the following :  1) At what voltage is the switching point? 2)…

A:

Q: Hello Sir. Good Evening. I have a question in my home work related Control System Lesson. The…

A:

Q: Qg: Find the value of k for stabk operation of the following characteri stic equantion I4 GooHCo)=…

A:

Q: . Below which is not a statement from an open loop control system is.... a. Less stable and less…

A:

Q: closed loop control system

A:

Q: The motor control system with the K1 Amplifier controller is shown in Figure P.2.b. It is known that…

A:

Q: Automatic kettle is an example of ________________________. a. Servomechanism b. Sequential…

A: The explanation is as follows.

Q: What are the steps for making a control project to the end? I want to answer in detail

A: The closing phase of control project involves these several steps. Formally transfer all…

Q: Question 1: What do the no-load characteristics of a DC shunt generator describe? A) The…

A: Since you have posted the questions with multiple subparts. So we are supposed to answer 3 subparts.…