VerticalQ6) The flow-metering device shown consists of astagnation probe at station 2 and a static pressure tapat station 1. The velocity at station 2 is 2 times that atstation 1. Air with a density of 1.2 kg/m3 flows throughthe duct. A water manometer is connected between thestagnation probe and the pressure tap, and a deflectionof Ah = 5 cm is measured. What is the velocity atstation 2?Water

Given:- Air with density=1.2kg/m3 deflection=5cm To find:- velocity at station 2

ion probe at station 2 and a static pressure tap on 1. The velocity at station 2 is 2 times that at 1. Air with a density of 1.2 kg/m3 flows through t. A water manometer is connected between the ion probe and the pressure tap, and a deflection

ion probe at station 2 and a static pressure tap on 1. The velocity at station 2 is 2 times that at 1. Air with a density of 1.2 kg/m3 flows through t. A water manometer is connected between the ion probe and the pressure tap, and a deflection

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1 A U-tube manometer is used to measure the pressure of oil of specific gravity 0.85 flowing in a pipe line. Its left end is connected to the pipe and the right-limb is open to the atmosphere. The centre of the pipe is 100 mm below the level of mercury (specific gravity- 13.6) in the right limb. If the difference of mercury level in the two limbs is 160 mm, determine the absolute pressure of the oil in the pipe. Liquid (5,-ERS) Pips
300 mmg 100 mmø H2O, 2) 500mm A 100mm diameter venturi meter is installed in a 300mm diameter horizontal main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 500mm, determine the discharge in the system assuming no head loss.
1. The manometers are suitable for comparatively C. very high A. low B. high pressures. D. none of the above
Q-4 The apparatus shown in the figure is used to measure the velocity of air at the center of a duct having a 10 cm diameter. A tube mounted at the center of the duct has a 2 mm diameter and is attached to one leg of a slant-tube manometer. A pressure tap in the wall of the duct is connected to the other end of the slant-tube manometer. The well of 10 cm p = 150 kPa the slant-tube manometer is sufficiently large that the elevation of the fluid in it does not change significantly when fluid moves up the leg of T= 20°C the manometer. The air in the duct is at a temperature of 20°C, and the pressure is 150 kPa. The manometer liquid has a specific gravity 30 of 0.7, and the slope of the leg is 30°. When there is no flow in the duct, the liquid surface in the manometer lies at 2.3 cm on the slanted scale. When there is flow in the duct, the liquid moves up to 6.7 cm on the slanted scale. Find the velocity of the air in the duct. Assuming a uniform velocity profile in the duct, calculate the…
Question 44 A calibration test of a 15-mm diameter circular sharp-edged orifice in a vertical side of a large tank showed a discharge of 760N of water in 60 seconds at a constant head of 6.50 m. Measurement of the jet showed that it traveled 3.20 m. horizontally while dropping 450 mm. Compute for the nearest value of the coeficient of discharge. O 0.60724 O None of the above O 0.64702 O 0.64027 O 0.67240 A Moving to another qestion will save this resnanse Quostion 44 af 48
a 150 mm by 50mm venturi meter is installed in an inclined pipe carrying oil. the venturi distance between the inlet and throat is 20cm. the flo is upward through the meter. a differential manometer containing mercury the (sp. gr=13.6) is attached to the inlet base and throat. compute the deflection of the mercury if the actual discharge of pipe is 0.55 m³/s. assume the venturi coefficient to be 0.97.
I need the answer to the question in fluid mechanics
For a Gage Reading of 25.3 Kpa, determine the following: (a). Elevations of the liquids in the open piezometer columns E, F and G. (b). The deflections of Mercury in the U-tube manometer neglecting the weight of air.
* Incorrect. An open, clean glass tube, having a diameter of 4.6 mm, is inserted vertically into a dish of mercury at 20°C (see the Video). How far will the column of mercury in the tube be depressed? -0.00214 m
A horizontal Venturimeter with inlet and throat diameters 300 mm and 100 mm respectively is used to measure the flow of water. The pressure intensity at inlet is 130 KN/m2, while the vacuum pressure head at the throat is 350 mm of mercury. Assuming that 3% of head is lost in between the inlet and throat, find, the value of Cd for the Venturimeter and rate of flow.
A manometer is attached to a tank containing three different fluids. Find the value of y in the mercury column in the manometer