Intravenous infusions usually are driven by gravity by hanging the fluid bottle at a certain height to counteract the blood pressure in the vein and to force the fluid into the body. The higher the bottle is raised, the higher the flow rate of the fluid. (Density of fluid = 1020 kg/m³). a) If it the fluid and blood pressure balance each other when the bottle is 1.2 above the arm level, determine the gage pressure of the blood (in kPa). b) If the gage pressure of the fluid at the arm level needs to be 24 kPa for sufficient flow rate, determine how high the bottle must be placed. (in meters).

Intravenous infusions usually are driven by gravity by hanging the fluid bottle at a certain height to counteract the blood pressure in the vein and to force the fluid into the body. The higher the bottle is raised, the higher the flow rate of the fluid. (Density of fluid = 1020 kg/m³). a) If it the fluid and blood pressure balance each other when the bottle is 1.2 above the arm level, determine the gage pressure of the blood (in kPa). b) If the gage pressure of the fluid at the arm level needs to be 24 kPa for sufficient flow rate, determine how high the bottle must be placed. (in meters).

Name: Intravenous infusions usually are driven by gravity by hanging the fl
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Intravenous infusions usually are driven by gravity by hanging the fluid bottle at a certainheight to counteract the blood pressure in the vein and to force the fluid into the body. Thehigher the bottle is raised, the higher the flow rate of the flu

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The plunger of the hydraulic lift in a gasoline service station has a diameter of 1 inch. It is operated by a compressed air (density = 63 kg/m3) from the tank in which the pressure is 9.315 x 105 pascals. The output piston and the rack on which the car rests are 2 feet lower than the input plunger and together weigh 1,336.33 newtons. What is the weight of the heaviest car that can be lifted if the output piston has a diameter of 1 foot? Assume 80% efficiency of the machine.
3. A container filled with water accelerates at 20 ft/s² up a plane inclined by a = 30°. The pressure at the top of the tank, point 1, is measure at 10 psi. The length of the tank is 10 ft, and its height is 5 ft. Determine the maximum pressure in the tank. Pt. 1 ax
What gauge pressure must a pump produce in order to pump water from the bottom of Grand Canyon (730 m elevation) to Indian Garden (1370 m)? Express your results in Pascals and in Atmosphere. Include given, fbd and solution
Fig shows a U-tube differential manometer connecting two pressure pipes at A and B. Pipe A contains a liquid of specific gravity 1.5 under the pressure of 110 kN/m². The pipe B contains oil of specific gravity 0.5 under the pressure of 216 kN/m². Find the difference of pressure measured by mercury as fluid filling U-tube in mm. The value of x and y are 2.1 m and 1.1 m respectively. Pa S ==<4 INI IN Intercont The Mercury level difference (h) in mm
Water flows in a channel with uniform curvature R. The channel has height h = 6 mm and width w=190 mm (normal to the drawing plane) as shown in Fig Q3. The curved part of the channel has a length of 1 =95 mm in the x-direction. You can assume that the channel height is very small compared to the curvature radius. Neglect effects of gravity. channel y V X 1 lower wall h upper wall centreline Fig Q3: Geometry of curved channel, drawing not to scale. The curvature of the channel is not shown, as too small to be drawn accurately at this scale. Work to 4 significant digits. Enter all values using base units or their combinations, i.e. m, m/s, Pa, N. Do not use multiples as e.g. mm, kPa. You can use values with exponents, such as 0.12e3.
Q1) Using a system similar to that shown in figure, compute the required air pressure above the water to cause the jet to rise h2 = 41 m from the nozzle. The depth h, -2.1 m. Air pressure
Q1. A trapezoid-shaped tank used to supply potable water to a small area which includes 8 villas (Figure 1). The tank bottom base is 3 m, while the top base is 5 m. The tank is partially submerged vertically in water so that the top is 1 m above the surface and the bottom is 3 m below the surface. Determine the total force exerted on the trapezoidal wall by the water. Vertical Pipe line from overhear tank Main distribution line Overhead tank Secondary distribution line Villa Villa Valve Villa Villa G.L. Venturimeter Villa Villa Villa Villa Junction Figure 1. Water Supply and Distribution System Q2. The water flows through a horizontal Venturi-meter at section 2 in Figure 1. The inlet and throat diameters are shown in Fig. 2 below. A mercury filled a U-tube manometer connected to the inlet and throat shows a difference in mercury level of 300 mm. The specific gravity of mercury is 13.6. Determine the flow rate, and the difference in pressure between the inlet and throat. Throat Area, AT…
2. A closed tank mounted on a truck 6m long, 2.50m wide, and 2m high is transporting oil (SG=0.85) at 85% capacity. Determine the a. required horizontal acceleration to the left causing a pressure of 5 kPa at the front wall. b. total force acting on the side with greatest depth. c. If the force at "b" is increased by 30 kN, what will be the new horizontal acceleration?