ructions: Using a W21x44 beam to support the loads, determine the maximum uniformly distributed loading (w, Kn/m) that the beam can support. Also, the allowable deflection is 1/500 of the san. Lastly, consider bending, shear and deflection using LRFD. 60 KN w, KN/m B 3.00m 3.00m 3.00m 3.00m

Q: A + 2.5 + 4 + 3m 3- Calculate 500kN H 4 + 4m D=25mm ku 66 D=35mm D=45mm Z=20x10 AVA-? M

A: E = 2 × 105 N/mm2 L1 = 2.5m = 2500mm L2 = 4m = 4000mm L3 = 3m = 3000mm Determine the vertical…

Q: The continuous one-way joist slab section shown over three spans of L=5m each is loaded with…

A: Given- L=5mDL= 3kN/m2LL=2 kN/m2ρ=12 Kn/m3

Q: a) An X mm rod length with Y mm diameter is put under tension load gradually in order to complete a…

A: Given, Diameter of sample = 2 mm Length of sample = 177 mm

Q: is one of the option to change the line Thickness. a. Zoom b. Linear c Bylaver

A: Zoom-  The function of this tool is to alter the zoom level of any working image.  Linear-This…

Q: -160 40 160 Dimensions 40 in mm 40 -160- –160-

A:

Q: 1) Reqd: Determine Maximum Shearing Stresses for the 3 segments and 0at C 2) F (2)Solid…

A:

Q: Pu 2. A 12mmx400mm steel plate has staggered holes arranged as shown. "b" 100mm' 100mm 100mm 60 mm…

A: A 12mmx400mm steel plate is given, we need to find out a. The distance "b"b. The critical net areac.…

Q: The beam cross sections shown are symmetric about the x and y axes. Determine the area moments of…

A: Given data,beam cross section is given top flange width =140mmheight=250 mmthickness of web =6…

Q: Calculate the number of theoretical plates needed to achieve a resolution of 1.50 for compounds with…

A:

Q: 4. Determine the crosssectional areas of members AG, BC, and CE for the truss shown in the figure.…

A: As per the given information we need to determine the cross sectional area of the members AG,BC,CE…

Q: Instructions: Solve the following problems completely Problem 1 12 kN/m 10 kN/m 8 kN 5 kN/m 5 kN/m 5…

A:

Q: The beam has a width of 300 mm and an overall depth of 500 mm. Design the spacing of critical shear…

A:

Q: 15mm

A: From a given figure it is required to calculate the centroidal distance from from x and y axis.

Q: aSN 200 mm 350 mm

A: Free Body Diagram (FBD):

Q: For the H - section shown, Find the value of h so that Ix = Iy. %3D 20mm 100mm 20mm h = ? 20mm 140mm

A: Moment of Inertia of Rectangle about C.G =bd312From Parallel Axis Theorem :Im=IG+Ax2Where Im= Moment…

Q: The column section shown above is reinforced with equal number of 20 mm bars on each face. Using f.…

A: Given:- The diameter of the bars used as reinforcing = 20 mm  The compressive strength of concrete…

Q: Calculate uniform load W that the cantilever beam can carry having a length of 3m. The section of…

A: Given: Span. L = 3 m fc = 25 MPa fy = 276 MPa Tension reinforcements, 5-#28 mm h = 650 mm hollow…

Q: Draw N, V and M diagrams and determine Mmax- 3 m 5t 2 t/m 5 t/m

A:

Q: Problem 6.2. The undeformed and deformed outline of a material element are as shown in the figure…

A: Consider the diagram as shown below. Now. And,

Q: Question 2 Calculate the maximum value of force G shown in Figure Q2, if the diameter of cach rod…

A: Given data  Diameter  Length Maximum permissible stress

Q: Given the following: b=380mm d=530mm fc'=30MPA fy=320MPa Mu=650KN-m Determine As A. USE NSCP 2015,…

A: Given,

Q: Please answer part C A = 150mm^2 E = 200GPa

A:

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: 6. Give one objective function used in model calibration and discuss its use, advantages and…

A: Model Calibration: It involves collection and analysing contemporary flow and pressure measurements…

Q: 4.157 Find the forces in members CD, DH, and HI.

A: The given figure is shown below:

Q: Q2. A tie member of a roof truss consists of two angles are connected to either side of a gusset…

A: Given: Properties of the Angle section =ISA 60×40×8 mm The thickness of the angle section, T = 8 mm…

Q: Where has the 311.2mm and 327.1mm and 15.8mm Come from ? That's what I don't understand

A:

Q: Compute Ix and Iy for the region shown. 40 mm 68 mm T 66 mm 66 mm 40 mm x

A:

Q: Solve for the shape factor of the section shown below 650mm 20mm 380mm 25mm 25mm +325mm +

A:

Q: 5. For the machine elements shown, locate the centroid. 12 mm 100 mm 62 mm 51 min SS mm 12 mm 10 mm…

A: Calculation of volume and distance from the reference line: V1=100×88×12=105600 mm3x1=1002=50 mm…

Q: Question 3 Consider a step shaft fixed at both ends and loaded with a torsional moment M, as shown…

A:

Q: 15 kips A AAB =1 in 2 ft ABp = 2 in E = 29,000 ksi 4 kips 4 kips B 1.5 ft 8 kips 8 kipg CE 1 ft

A: To find the displacement at A relative to D -

Q: Strength of Materials HOME WORK 3 – Combined For the assembly shown in the figure below, Determine…

A:

State Plane Coordinate Systems

The state plane coordinate system (SPCS or SPS) is a collection of 124 coordinate systems or geographic zones prepared for particular regions of the U.S. Every state consists of one or more than one state plane zone, the boundaries of which generally follow the county lines. Inside the U.S., there are 110 zones in total, 10 more zones in Alaska, 5 in Hawaii, and 1 for Puerto Rico and US Virgin islands. The system is extensively used for geospatial and geographic data assembling by the state and local governments.