Instructions: In this exercise, incomplete relationships are set up among fluid conductors and connectors. Complete the suggested relationships by choosing the appropriate word or phrase from the choices at the end of the exercise. 1. hose: flexible/tubing: 2. pipe: nominal/tubing: 3. L.d. too small: inefficient / wall too thin: 4. tubing: straight-line assembly/hose: 5. pipe: schedule/hose: 6. hydraulic systems: double shutoff/pneumatic systems: 7. tubing: flareless/hose: 8. hose: very high pressure / pipe: 9. pipe threads: 1/16" taper / flared fitting: 10. stationary: pipe/moving: A. hose B. no-skive C. o.d. D. reinforcement E. schedule 160 F. semirigid G single shutoff H. stretched tight I. 37° or 45° J. unsafe

Q: (b) The steel shaft has a diameter of 40 mm and is fixed at its ends A and B as shown in Figure…

A: For solution refer below images.

Q: dy = m y2 dx

A:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: Convert the octal number 23228 to its hexadecimal number equivalent, (base-8 to base-16).

A: Steps of Conversion: The simplest way is to convert the octal number into a decimal, then the…

Q: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

A: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

Q: Draw the symbol for the following valve and number the ports according to our numbering convention..

A: The given valve is the 4/3" data-mce-style="display: inline-block; line-height: 0; text-indent: 0px;…

Q: A 29/32 icnh hole must be enlarged to 59/64 inch to insert a bushing. How much wider than the…

A: To find out how much wider the hole will be after enlargement, we need to calculate the difference…

Q: 10. Complete sketch A to show the significance of the welding symbol shown in sketch B.

A: This is a double J weld Configuration Problem which consist of different radius on both side.

Q: How did you get theta =45?

A: Consider following given figure of a structure.here we need to determine the angle between member DE…

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: mpute the Degree of Freedom (DOF) for the given Kinematic diagram

A: To determine the Degree of Freedom of the given kinematic diagram.

Q: "Sarcomere"

A: option b) part between two Z line

Q: Describe thrust angle.

A: Introduction  The thrust angle is basically used as a major angle for alignment of the rear and…

Q: L t C Determine the moments at fixed ends 'a' and 'd' ?

A:

Q: FORTUNE FAVOURS THE BRAV

A: A week ago our little villa was invaded by fear-based oppressors. There was dread in the seniors.…

Q: What unit is the 0.000931 ?

A: Torsion equation is given by, TJ=τr=GθLwhere,T = torque acting or applied in N-m or N-mmJ = polar…

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: What is that number in red above Ey in Figure 3?

A: Consider following free body diagram showing forces acting at point E

Q: what happened with the 10 in the first equation?

A:

Q: how did you find d1 and d2

A: This question is based on the concept of polar radius.

Q: Iron Ore are mainly used to produce high heat in blast furnace

A: I think its answer should be False. Because blast furnace is used to melt iron ore by reducing…

Q: State four espect to consider before selecting correct solvant

A:

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: QI Define five of the following with sketch. 3- AA2024 4- Rolling 5- Wire drawing 1-Taper turning 2-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: idk where you got the 4 from

A: The number of independent equations=5The number of unknowns=7To determine:Degree of freedom

Q: what is the bottom length?

A: To calculate the bottom length

Q: question: The degrees of freedom of the calculation package in the figure?

A:

Q: what is the omega value? as per the professor, the IC is at b not a

A: Given: The velocity of the upper wire: →V=5.6 m/s It is right that the instantaneous center of…

Q: . Convert the octal number 23228 to its decimal number equivalent, (base-8 to base-10).

A: Givenoctal number =23228

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: Question 6 Classify the following parts, giving reasons for your answers: (a) A speed indicator for…

A: **As per our company we are supposed to do only 3 sub part if you need the rest please upload that…

Q: Create a table showing wrench sizes in metric and U.S. units.

A: Following are the wrench sizes in metric and U.S. units.

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: SI) Standard Sizes of Woodruff Keys 1210?

A: The dimension of ANSI 1210 KEY IS GIVEN AS

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: Is this for number 1 only?

A: