Instead of using the system shown in Figure 3.2.6a to raise the mass m2, an engineer proposes to use two simple machines, the pulley and the inclined plane, to reduce the weight required to lift m2. The proposed design is shown in Figure P3.12. The pulley inertias are negligible. The available horizontal space limits the angle of the inclined plane to no less than 30°. a. Suppose that the friction between the plane and the mass m2 is negligible. Determine the smallest value m1 can have to lift m2. Your answer should be a function of m2 and 0. m₂ m₂8 (b) T₁ m₁ mig x

Instead of using the system shown in Figure 3.2.6a to raise the mass m2, an engineer proposes to use two simple machines, the pulley and the inclined plane, to reduce the weight required to lift m2. The proposed design is shown in Figure P3.12. The pulley inertias are negligible. The available horizontal space limits the angle of the inclined plane to no less than 30°. a. Suppose that the friction between the plane and the mass m2 is negligible. Determine the smallest value m1 can have to lift m2. Your answer should be a function of m2 and 0. m₂ m₂8 (b) T₁ m₁ mig x

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4) This Atwood's machine includes two blocks connected by a cable, going over a pulley without slipping. Block 1 (30.0 kg) is connected to a spring (70.0 N/m), and slides on a horizontal surface with a coefficient of kinetic friction of 0.0100. Block 2 is 50.0 kg, and hangs vertically from the cable. The pulley is a disk with a radius of 0.500 m, and its moment of inertia about the center of mass is 10. 0 kg-m“. a) Draw the three free body diagrams, and write out Newton's 2nd Law for each. b) Derive the equation of motion (inhomogeneous 2nd order ODE) for this system. c) Use u-substitution to rewrite this as a homogeneous 2nd order ODE. d) Assume the position x as a function of time t is of the form x(t) = A cos (wt + p) I disk for undamped natural frequency w, phase angle P, and amplitude A. The initial conditions are: x(0) v(0) = -3. 00 m/s. Solve for the position of the mass as a function of time (you need to solve for w, 4, and A). = 2. 00 m and Mz
For masses and are 200 kg, 300 kg, 240 kg, and 260kg respectively. The corresponding radii of rotation are 0.2m, 0.15m, 0.25m and 0.3 m respectively and the angles between successive masses are 45 , 75 and 135 . Find the position and magnitude of the balance mass required, if it’s radius of rotation is 1.4 m.
2. For the system below: a. Give an equation of motion for h. Note that the system has two inputs, p1 and p2. b. When h= 5, give the force exerted on the bottom of the tank. (Assume that the width and height of the opening at the bottom of the tank is negligible. The area of the bottom of the tank is A). h PA PI P2 PA R
The input and output pistons of a hydraulic car lift have diameters of 3.00 in and 25.0 in, respectively. A 2890 lb car is raised through a height of 5.00 ft above the garage floor. (a) What is the input force? (b) What is the distance through which the input piston moves?
c) The pulley system shown in Figure Q1c lifts a mass, m, of 550 kg. Calculate the force FAnecessary to maintain the suspended mass in static equilibrium; and determine the forces at the ceiling anchor points A and B. Assume frictionless and weightless pulleys and use g 9.81 m/s.
Can you please help me with all parts of the question? Thank you
A block and sphere are connected by a cord that passes over a pulley as shown. Neglect friction and assume the cord is massless. Take m1 = 2.00 kg, m2 = 7.65 kg, and ? = 49.0°. A triangular structure is oriented such that its base rests upon a horizontal surface, its left side is perpendicular to its base, and its right side forms an incline of angle ?. A pulley is attached to the structure's apex. Two objects are connected by a cord that passes over the pulley. A circular object labeled m1 is attached to the to the left end of the cord and hangs freely. A rectangular object labeled m2 is attached to the end of the cord and rests upon the incline. (a) What are the magnitude of acceleration (in m/s2) of the block and sphere? _____m/s2 (b) What is the tension (in N) in the cord? (Enter the magnitude.) ____N (c) What is the speed (in m/s) of each object 2.25 s after being released from rest? ____m/s (d)What If? If the incline under m2 is rough, what is the minimum value…
Six masses m1, m2, m3, m4, mM and mL, shown in figure below are to be completely balanced. The masses are : m1= 20.11 kg, m2 = 2 kg, m3 = 3 kg, m4= 6.3 kg, mM = 10.23 kg. The radii are : r1 = 0.1m, r2 = 0.12 m, r3 = 0.14 m, r4 = 0.12 m, rM = 0.1 m, rL = 0.5 m. The angles shown in the figure are: θ1 = 12º, θ2 = 103º, θ3 = 135º, Φ = 32º. The distances between different planes , shown in the figure are as follow: l1 =0.8 m, l2 = 0.7 m, l3 = 2.44 m. we need to find lm, l4 , mL and the angle α
A mass weighing 11.5 kg falls a distance of 1.5 m upon the top of a helical compression spring. Determine the force applied on the spring if it compressed 203mm. Please show your full solution with unit analysis. Subject: Machine Design