Inside a machine, two gears, A and B, HINGED at their centers, are meshed with each other such that gear A transmits torque and speed to gear B. Gear A has a mass mA=2 kg, radius rA=175 mm, and radius of gyration kA=150 mm. Gear B has a mass B=5 kg, radius rB=525 mm, and radius of gyration kB=400 mm. From rest, a counter-clockwise couple M of constant magnitude 6 Nm is applied to Gear A.  Which of the following is closest to the magnitude of the angular acceleration of gear B, in radians per square seconds (rad/s2)? 3.00 44.8 14.94 45.6

Q: Mechanism shown consists of two 8-pound rods AB and CD. each and a 10 lab AD bar. When θ = 0 °, the…

A:

Q: 8. The mass of the gear wheel is ma = 50 kg and the radius of inertia kO = 125 mm. Rack B stays in…

A:

Q: Slider 1 is moving downward at a speed of 1 = 2 m/s and with a downward acceleration of a = 0,25 m/s…

A: Dear StudentsAll the solution given in below steps

Q: A 7.5 kg disk A radius of 0.6 m initially rotating clockwise at 300 rev/min is engaged with an 8.5…

A:

Q: The spool has a weight of 40 lblb and a radius of gyration kOkOk_O = 0.4 ftft . A cord is wrapped…

A:

Q: 2 An object is made of two identical uniform 3m long rods connected as shown. The total mass of the…

A:

Q: The uniform, thin 5-lb disk spins at a constant rate w2 = 6 rad/s about an axis held by a housing…

A: The data given is, Angular velocity in x-direction, ?x = ?1 = 3 rad/s Angular velocity in…

Q: A homogeneous disk of mass m = 7 kg rotates at the constant rate w₁ = 12 rad/s with respect to arm…

A:

Q: 3) A 40 kg uniform disk rolls without slipping up an inclined plane. In the configuration shown, the…

A:

Q: Flywheels A and B are mounted on light coaxial shafts which can be coupled by means of the clutch C,…

A: Given; IA=0.6 kgm2ωA1=3410 rev/minωB=800 rev/minω=1750 rev/min

Q: Which of the following best approximates the angular velocity of the system at position 2? a.…

A:

Q: A wheel fixed about O has a weight of 4 lb and a radius of gyration ko = 0.8 ft. What torque is…

A:

Q: The 10-oz disk shown spins at the rate w1 = 750 rpm, while axle AB rotates as shown with an angular…

A: The angular velocity vector is: Let the origin be at C with the centroidal axis x, y, and z.

Q: = Gear B has an angular acceleration of a b 0.15t² rad/s², where t is in seconds, and an initial…

A: Angular acceleration of gear B→αB=0.15t2  ...............equation1→dωBdt=0.15t2→ωBf-ωBi=0.15t33…

Q: In the image on the right, there is a red gear G1 on the left with a radius of r1 = 2.81cm. Gear G1…

A:

Q: 4. A pair of connected pulleys receive a force F = 75 N and P = 150 N as depicted in the image. The…

A:

Q: The mass of gear A is 25 kg and its centroidal radius of gyration is 105 mm. The mass of gear B is…

A:

Q: Two identical uniform slender rods with length 2.2 m and mass 3 kg are pin-connected at A. One of…

A: Given:The length of each rod, The mass of each rod, The angle made by the rod OA with horizontal,

Q: Two identical rods AB and BC form an L-shaped assembly. The assembly is pressed against a spring at…

A: Moment of inertia about B, IB=1/2mABl2+1/3mBCl2 position2 V2=WAB(hAB)2+WBC(hBC)2    =WABl/2 sinr…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.