Input shaft of the gear train shown below rotates at 1,500 RPM. The output shaft must rotate exactly at 100 RPM. Minimum number of teeth can not be less than 20 and the maximum numbor of teeth can not be more than 150. The speed of goar B must be exactly 500 RPM. Determine tho speed of gear C: Note: This is a short answer type question with limited space for answor. Therefore, write the answors and do not show any other details. Input pinion A N= 20 teeth W,= 1,500 rpm No B

Input shaft of the gear train shown below rotates at 1,500 RPM. The output shaft must rotate exactly at 100 RPM. Minimum number of teeth can not be less than 20 and the maximum numbor of teeth can not be more than 150. The speed of goar B must be exactly 500 RPM. Determine tho speed of gear C: Note: This is a short answer type question with limited space for answor. Therefore, write the answors and do not show any other details. Input pinion A N= 20 teeth W,= 1,500 rpm No B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Bevel Gear A pair of bevel gears connects shafts at right angle with speed ratio of 2:3. The larger gear has 30 teeth with 4-tooth per inch diametral pitch. The gear is made up of 20°involute full depth. Determine the following: a) the number of teeth of pinion b) the pitch angle of gear c) the pitch angle of pinion d) the pinion diameter e) the gear diameter f) the length of cone g) the expected value of addendum h) the expected value of addendum angle i) the face angle of pinion j) the face angle of gear k) the dedendum l) the dedendum angle m) the cutting angle of pinion n) the cutting angle of gear.
8. A pinion gear with 15 teeth turns at 200 rpm ('revolutions per minute). It is driven by a larger gear having 60 teeth, What is the rpm of the larger gear? (Hint: Write a proportion showing that the products of the number of teeth and the speed (rpm) of each gear are equal.) O O O O 50 75 600 800
b) Figure Q1b shows a compound gear train with Gear A as the pinion (or driver) with an input Power (Pin) of 600 W at Gear A. If Gear A rotates at 139.70 rpm and engages with Gear B, calculate the angular velocity (w) in rad/s for Gears B, C & D; and the input torque (Tin) in at Gear A and output torque (Tout) at Gear D. The number of teeth (N) for gears A, B, C & D are 62 teeth, 34 teeth, 42 teeth and 22 teeth, respectively. Assume 100% efficiency and no frictional losses; and give your answers to two decimal places. GEAR A GEAR C GEAR B GEAR D
lay in Sign In to LinkedIn Number of teeth are indicated for the following gear train. Driver gear 2 has speed 1200 CW direction. Find the speed of gear 5. rpm in 10T 3 30Т 4 16T 32T (a) 200 rpm CCVW. · (b) 200 гpm CW. (c) 300 rpm CW (d) 300 rpm CCW.
Qestion-3: For the gear train shown identify which of the rack-gear will move faster (Gear-COR Gear-R) and how many modulos are powible? C and R: Rack Gears Dand B: Compound Gears R
2. The following data is for the gear train shown in the figure: Given: N2 = 30t, N3 = 35t, N4 = 55t, N5 = 40t, N6 = 50t, N7 = 40t %3D w2 = 30 rpm ccw, warm = 20 rpm cw, Input torque on gear 2 is 1200 lbf.in Determine the following: a. Angular velocity of the sun gear. b. The gear ratio R required to determine the angular velocity of gear 6. c. The angular velocity of gear 6. d. The angular velocity of gear 7. e. Output torque on gear 7. Be careful with your units. Arm 6 ... 7
If Gear C and gear A are having the same pitch diameter gear and gear B is twice (larger) the diameter of gear C. If gear C is turning at the speed of 50 RPM, what would be the Rotational speed of Gear B in RPM. (RPM = revolution per minute)
3. A gear having 48 teeth is being driven by a 12-tooth gear running at 800 rpm. Determine the speed of the driven gear if a 24-tooth idler is placed between the driving and driven gear. Note: Draw the gears showing their direction of rotation.
A hole is to be drilled as shown by the circle. Using the part geometry shown below, indicate on the part sketch where locator(s) should be positioned according to the 3-2-1 principle. Use dashed lines to indicate locators on hidden surfaces. Also indicate where clamping force(s) should be applied using arrows. Use the minimum number of clamping forces.
Consider the gear train below where Gear D has 80 teeth and Gear A is spinning with 600 rpm. D 60 teeth the A 40 teeth 20 teeth a. What is the speed of Gear D? We want to adjust the gear train. We can only change out Gear C for a different sized gear. Gear A will continue spinning with 600 does our new Gear C need to have so that Gear D b. How many teeth rpm. spins with 200 rpm? B.
# Teeth on gear Pinion RPM # Teeth on pinion Gear RPM 60 X 90 270 Using the information from the chart in question 6 above answer the following. What is the ratio of the gear rpm to the pinion rpm in its lowest terms?