industrial motor runs on 486 Volts and 60 hertz. Find the Maximum Current, Effective Current, Average Current, and Instantaneous Voltage if the motor has a resistance of 304Ω. Also, how long does it take in milliseconds to complete a 1/16 cycle it t=2.56 s

Q: A coil is used for producing a flux of 0.24 x 10 webers. If the current flowing in the coil is 2 amp…

A: Given: Coil producing flux, φ=0.24×10-3 Wb. Current flowing in coil, I=2 amp. Coil turns, N=200.

Q: Introduction Explanation of Maximum Power in DC

A: In a d.c. circuit consisting of a resistor connected in series to a voltage source, the current…

Q: Iron losses in a DC machine are independent of variations in

A: The explanation is as follows.

Q: 10. A potential difference of 250 V is applied to a field winding at 15-C and the current is 5 A.…

A: First Calculate the resistance of winding at 15°C: R15=2505R15=50 Ω Now Calculate the resistance of…

Q: I need help understand on the question of how does the vertical shift compareto the dc level of…

A: The amount of shift in vertical axis in case of DC mode gives us the DC value of the battery.  In…

Q: A 12 V DC electrical motor draws a current of 18 amps, How much work does this motor produce over a…

A: Work done by DC motor is calculated as shown below

Q: A universal series motor, when operating on 220 V d.c. draws 10 A and runs at 1419 r.p.m. Find the…

A: Universal motor is a motor, as the name suggests, an electric motor capapble of running on both AC…

Q: A coil has 480 turns and flux in it changes from 0.24 m Wb to 1.2 m Wb in 0.24 second. Calculate the…

A:

Q: An electron synchrotron of 6 x 109eV, electrons march through the machine in a roughly circular path…

A: Given R=240 m Q=1011electronsQ=1011×1.6×10-19Q=1.6×10-8

Q: 5. A welder machine operates automatically as follows : 30A current in 10 seconds, 20A in 10 sec.,…

A: In this question we will find RMS value of given waveform....

Q: Q3: A universal fractional horsepower series motor has a resistance of 30 Q and a total inductance…

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: Find the mechanical speeds in revolutions per minute of a multipole electrical machine, if the…

A: In this question,  If the frequency f= 50Hz. Find the speed N?  We know N= 120f/P

Q: A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of…

A: Given data, Time constant,τ= 10 msec Voltage source V = 10 KV = 10000 V Discharging current is,…

Q: Which of the following is NOT a variable in voltametric methods? A. How the current is applied B.…

A: In this question we need to choose a option which is NOT a variable in voltametric methods.

Q: When an electric generator is in operation, it is driven or rotated by a mechanical machine that…

A: We need to tell about the system which converts the chemical energy to mechanical energy .

Q: A simple electric motor needs to supply a maximum torque of 10 Nm. It uses 0.1 A of current. The…

A: According to question:

Q: proximately, how long does it take the circuit to have a current near 5A upon closing of the ritch?…

A:

Q: Due to an armature reaction in DC mach the generated volt is O Decrease O Increase or decrease O…

A: In this we will write about generated voltage in dc machine due to armature reaction...

Q: The meter constant of a single phase 230 V, induction energy meter is 800 rev/ kWh. What will be the…

A: Given: For a single phase energy meter V=230 VI=20 Acosϕ=0.7 lagMeter constant=800 rev/kWh

Q: A coil has a time constant of 1 second and an inductance of 10 H. What is the value of the current…

A: The solution is given below

Q: You have a 150 [kW] DC motor with an efficiency of 92% operating at full-load. The losses in the DC…

A: Given data, Output power= 150KW Efficiency = 92%

Q: Exercise: What will be the o/p of the following meters? F.W.R H.W.R D'Arsonval Dynamo. meter PMMC…

A: Analog instruments are classified into 3 types Indicating instrument Integrating type instrument…

Q: When a 5 A current is made to flow through a coil of 20 turns produce a flux of 10 Wb. Find the…

A: Given: A coil with Number of turns, N=20 Current through the coil, i=5 A Flux produced, ϕ=10 Wb Rate…

Q: What is the resistance to the changing flow of alternating current? Select one: A. AMPERES B.…

A: In electromagnetism and electronics, inductance is the tendency of an electrical conductor to oppose…

Q: The maximum amount of voltage is induced time(s) in 3600 of mechanical rotation for a single loop…

A: The explanation is as follows.

Q: A universal series motor, when operating on 220 V d.c. draws 10 A and runs at 1400 r.p.m. Find the…

A: Given: A universal series motor, when operating on 220 V DC draws 10 A and runs at 1400 rpm and when…

Q: The armature of a 60 Hz ac generator rotates in a 0.45 T B-field. The area of the coils is 0.06 m2.…

A: The solution is given below

Q: A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of…

A: When a switching device is in it's reverse recovery states, various charge carriers recombine. This…

Q: Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. The coil of a generator has an…

A: In this question we will find temperature of coil with given resistance value...

Gear Motor

A gear motor is a combination of a gearbox and an electric motor. This combination of two systems is used for efficient usage of the motor. It makes a cost-effective solution for high torque, low-speed applications. These motors are used in our household as, garage door openers, alarm clocks. In commercial areas, hospital beds, cranes.