induction A 440V, 3-1, 50 Hz, 6-pole, Y-connected motor has a full load speed of 950 rpm. The rotor has a stand still impedance of (0.3+/5) ohm and rotor to stator turn ratio of 0.85. Calculate the rotor current at full load (A) 47.88 A (C) 27.64 A (B) 56.33 A (D) 32.52 A

Q: Q) All type of indicating instruments are passive and Null type * От

A: solve above ques

Q: 1. Signed 2's Compliment numbers Convert the following signed 2's compliment values to the decimal…

A: We need to find out decimal equivalent , for given binary number .

Q: function, turning the LED This set/reset circuit controls D2. Closing SW1 controls the ISelect] […

A: The circuit follows SR latch as mentioned in the question. The truth table is as shown below; The…

Q: Duty: design a hand counter according to the following order from left to right 4, 5, 0, 1, 3, 7…

A: SEQUENTIAL LOGIC CIRCUITS: Sequential Logic circuits, unlike Combinational Logic circuits, have some…

Q: I. QUESTIONS/PROBLEMS 1. How are plus and minus current signs determined?

A:

Q: BNC connectors are used in CCTV [True/False]

A: In this question we will write about BNC connectors...

Q: Test the compute the 2 complement result and notice that you have to test the overflow if it does…

A: All the three numbers that are given in the above question are represented in format of 3 bit 2's…

Q: In N-channel JFET the Id is controlled by_______. a.Idss b.Vgs c.Vds d.Ig

A:

Q: Perform Analysis of above given Sequential Circuit

A: According to the question,  we need to find the expression for the output of the given circuit. Let…

Q: Can you redo this again? I need step-by-step solution, like there should be Step 1, Step 2, Step 3,…

A:

Q: c) Given the changed lines of code below, answer the following questions. ANALOG_COMPARE_SETUP: LDI…

A: The given code is shown below.ANALOG_COMPARE _SETUP:LDI R16,0STS ADCSRA, R16LDI R 16, 0b00000000STS…

Q: The degree of precision of a quadrature formula whose error term is : f(4) (5) is 3 O 1 4 O 2

A: The degree of precision of a quadrature formula is in if and only if the error is zero for all…

Q: Q3/Find the solution of the following operation for octal number 717*0.33 301.05 237.05 303.25…

A: here we have to perform multiplication of the octal numbers. given operation is 717*0.33

Q: 2. Compute carry and overflow flags in the following table. Carry Overflow Operation 0100 0110 0101…

A:

Q: Explain in words the relationship between m18 and m19

A:

Q: Convert (11010001.0111)2 into Oct.

A:

Q: Explain what is a stiff supply system ? What is its importance in harmonic environment? ARC

A: To explain the stiff supply system

Q: odd parity is selected on a tow bit parity generator and data A= LOW , B= HIGH the parity bit will…

A: This is based on the odd parity If the odd parity is selected on a two bit parity generator and data…

Q: QUESTION 9 With reference to the instruction below, what is the value of the number stored at N7:20…

A: We need to select correct option for given instructions.

Q: Problem_#03] For the ripple counter below, complete the timing diagram for eight clock pulses. HIGH…

A:

Q: For the following circuit, values of QO, Q1 are only observed at select time indicated by the dashed…

A: At every +ve clock edge, D0 will change its output At every -ve clock edge, D1 will change its…

Q: 4. Subtract (00110011)2 from (01110101)2 using Normal, 1's complement and 2' complement subtraction.

A:

Q: CLK T Positive Edge Triggered T Flip Flop LAH CLK T Negative Edge Triggered T Flip Flop I I

A:

Q: Need help finding TF

A: Given: Block diagram of a control system. Formula and concept: Transfer function: Transfer function…

Q: C:- How many NOT gates and AND 4 poi gates are required for the construction of a 1-to-16 De-…

A: Demultiplexer-DEMUX is a combinational circuit that takes a single input line and routes it to one…

Q: Impedance inversion can be achieve using

A:

Q: Which of the following statements about the TRIAC is true: O A. None of the other choices are…

A:

Q: clk in1 in2 out 0 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16

A: We need to tell about type of flip flop for given input and output .

Q: select the right answer: The remainder in cyclic redundancy checking represents the a. The CRC b.…

A: the error

Q: For the following circuit, values of QO, Q1 are only observed at select time indicated by the dashed…

A: The given circuit contains a D flipflop and the output of the flipflop is the same as the input…

Q: for Vth it was supposed to be 26.6 not 20.0 apologies for the handwriting

A:

Three Phase Induction Motor

The induction motor is an electric motor that runs on AC (alternating current) and it is of two type single phase motor that work on single-phase power supply and three-phase motor that work on three-phase power supply.