'ind the intrinsic camera matrix K re the camera pixels skewed? pes the camera have unit-aspect rati

Q: What does the stress in a composite beam depend on? O the modulus of elasticity of both materials…

A:

Q: For the compressor shown in the following figure, find the position of the piston with respect to…

A:

Q: Find the acceleration in terms of F. 回 m₁

A:

Q: expression p = K(x - x) where x is in cm and k in mV-cm. a. Find the divergence of p for k=1/2…

A:

Q: The sides AB and CD of a quadrilate 2. ABCD are extended to points P and respectively. Is ZADQ+ ZCBP…

A: Following are some standard geometrical figure 1) Triangle 2) Rectangle 3) Circle 4) Quadrilateral A…

Q: Past ME Board The following coa C = 70.5 % S = 3.0% A stocker fired b fuel. Calculate th pressure if…

A: Given: C=70.5%; H2=4.5%; O2=6%; S=3%; N2=1%; Ash=11%; and Moisture=4%.A stocker fired boiler of…

Q: 12. The gear A on the drive shaft of the outboard motor has a radius r = 0.5 in. and the meshed…

A: Introduction: In an assembly, a pinion is the smallest of two meshed gears. Depending on the…

Q: Calculate the DOF (mobility). Show your accounting for L, J₁, J. Given: M-3(L-1)-2J₁-J

A:

Q: 5. An ideal Otto engine, operating on an air standard with k=1.35 has a compression ratio of 5. At…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a…

A:

Q: Determine the magnitude of the internal loads(normal, shear, and bending moment) at point C.

A: The given member can be cut into two parts along C and the above part can be drawn as below, Here,…

Q: The force F shown below is applied in the positive x-direction against a 20-degree slope. The force…

A:

Q: Resolve the 900-N force into a component P along with AB and a component Q perpendicular to AB. B…

A:

Q: The pressure of a gas in piston-cylinder varies with volume according to PV=C. The initial pressure…

A:

Q: 2 Example 15-24 building 60m high. and vith what velocity will it strike the ground? An object falls…

A:

Q: You are expected to design a simulation environment for a bicycle with a kinematic model. The…

A:

Q: For the mechanisms shown below determine the number of links, full joints, half joints and the…

A: The solution is provided below.

Q: C2(i)Assume that annual energy requirement of an industry is 20900 kWh ,we calculate that what will…

A: Given  Annual energy requirement= 20900kWh Coefficient of performance = 0.4 Loss factor value =…

Q: Question 13 Solve the problem. Find the work done by a force of 200 pounds acting in the direction…

A:

Q: 6/9 A uniform slender rod rests on a car seat as shown. Determine the deceleration a for which the…

A:

Q: Suppose potential p in millivolts is given by the expression p = k(x? - x) where x is in cm and k in…

A: Given: Potential→ϕ=kx3-x2 where k is arbitrary constant And x is the distance in x direction.…

Q: Hanf written plzzz asap.plzz i'll rate sure

A:

Q: he figure shown is the cross section of an endspan of a fully restraine eam that carries a moment of…

A:

Q: 2.59 The mercury manometer of Fig. P2.59 indicates a differen- tial reading of 0.30 m when the…

A: Pressure at A  PA=γHghA=S.G×γwhA=30×10-3×13.6×9810=4002.48 N/m2 (Vacuum)

Q: The hydraulic cylinder imparts a constant upward velocity VA = 0.27 m/s to corner A of the…

A:

Q: Obtain mathematical models of the mechanical systems shown in Figures (1 and 2). x (Output) u(1)…

A: part 1we can see thatspring are in series Keq =11K1+1K2   =K1K2K1+K2

Q: Explain the role of manufacturing in design?

A:

Q: 90

A: data we have    given P =100 kgm2      Ab = 25m/s2   massm =P×area                 = 100 kgm2×πr2…

Q: (b) Water at 10°C is flowing steadily in a 0.12 cm diameter, 15 m long horizontal pipe at an average…

A: Given:d=0.12 cm =0.0012 mL=15 mV=0.9 m/sθ=30°

Q: Design a chain drive for 20hp and 800rpm vith an output speed on other sprocket of 200-300rpm

A:

Q: Design a chain drive for 20hp and 800rpm with an output speed on other sprocket of 200-300rpm

A:

Q: A pulley system made up of 3 pulleys, is used to lift a load of 10kg through a height of 50cm. If…

A: Mechanics problem can be solved as:

Q: at A has coordinates (0, 0). If a load P acts on the ring at 3 becomes EAB = 0.02 in/in., and the…

A: data providedthe length of  rod AB LAB = 5 in the length of rod Ac ,LAC = 8 in The normal…

Q: Calculate the dimensions of the I-section of a connecting rod, stating any assumptions. using the…

A: To calculate the dimensions of I section of the connecting rod givenmaximum cylinder pressure…

Q: unger -Highly permeable Magnetic material 2w Mass M Depth d perpendicular to page v, A N turns…

A: From given circuitVS(t)=i(t)R+Ldi(t)dtnow rearrange above equationLdidt+Ri=VS…

Q: Air is heated in a 4cm×4cm sheet metal duct with a uniform surface heat flux of 590 W/m2. The mean…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.