In using the bolt cutter shown, a worker applies two forces to the handles. Determine the magnitude of the forces exerted by the cutter on the bolt when P= 360 N.The magnitude of the force exerted by the cutter on the bolt is kN.Note: please show correct working out and final answer!. Thanks In using the bolt cutter shown, a worker applies two forces to the handles. Determine the magnitude of the forces exerted bythe cutter on the bolt when P= 360 N.P24 mm12 mm24 mmBE24 mm460 mm-96 mmThe magnitude of the force exerted by the cutter on the bolt is55.2KN.

Step 1:Given data :P=360 N Step 2:∑Fx=0;Bx=0∑MA=096*By-24*F=0F=4By ...(1)Step…

In using the bolt cutter shown, a worker applies two forces to the handles. Determine the magnitude of the forces exerted by the cutter on the bolt when P= 360 N. P 24 mm 12 mm 24 mm B E 24 mm 460 mm- 96 mm The magnitude of the force exerted by the cutter on the bolt is 55.2 KN.

In using the bolt cutter shown, a worker applies two forces to the handles. Determine the magnitude of the forces exerted by the cutter on the bolt when P= 360 N. P 24 mm 12 mm 24 mm B E 24 mm 460 mm- 96 mm The magnitude of the force exerted by the cutter on the bolt is 55.2 KN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4 - Two circular shafts are connected via a gear assembly as shown in the figure. Shaft 1 is fixed to a wall at point A. Torque T is applied to shaft 2 at point D. Shaft 1 is made of steel with a shear modulus of 85 GPa; shaft 2 is made of aluminum with a shear modulus of 28 GPa. The other relevant paramters are indicated alongside the figure. The shafts are restrained by bearings such that they do not undergo bending (i.e., it is a case of pure torsion). Determine the angular rotation at point D relative to that at point A. Shafts L₁=1.5m; L₂=1m r=50mm; ₂= 25 mm gear radii R₁-200mm; R₂=40mm Torque T=4KN-m Li C L2 * assume the gears to be rigid T
A T₁ Co B S T₂ C L₂ T3 L3 T4 O The image above shows a solid shaft with various torques applied in the directions shown. The values for each torque are as follows: T₁ = 800 N•m, T₂ = 600 N.m, T3 = 400 N·m, and T4 = 200 N·m. The values for the maximum shear stress in each section are as follows: TAB = 75 MPa, TBC = 90 MPa, and TCD = 100 MPa. Find the minimum allowable shaft diameter.
For the assembly shown, as the screw is tightened down, the strain in the horizontal direction at B is 900×106 m/m. What is the load P on the screw. E= 200 Gla.= of le 20 60 20mm hans s 201 Bo 40 Section a-a 104mm a← 120mm IT. at 300 mm →
For the following problem please show intermediate steps including free body diagrams, equation used, problem setup etc. so that your approach can be followed. Finally please put the answer in a box with the appropriate unit.
Mention the type of stress developed in the pin of bell crank shown in figure. Also determine the stress in the pin for given loading. The diameter of the pin is half inch.
Please answer only number 1 with complete solution (all computations must be 4 decimal places)
please show complete solution and avoid truncation in the middle of the solution. Thank you. (EXACT ANSWERS ONLY)
For the beam shown, EI = 24 × 10° kip-in² over the length of the beam. The slope (rad) of the beam at location B is most nearly: MA = 60 ft-kips A EI=24 x 106 kip-in² L=24 ft B MB = 120 ft-kips Please show all work, i am only interested in how to solve the propblem since i already know the final anser to be .0072 rad
Please show complete solution and explanation thank you
Part A If the required clamping force at the board A is to be 85 N, determine the torque M that must be applied to the handle of the "C" clamp to tighten it down. The single square-threaded screw has a mean radius of 10 mm, a lead of 3 mm, and the coefficient of static friction is u, = 0.35. Express your answer to three significant figures and include the appropriate units. M = 1.1142 Nm O The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Submit Previous Answers Request Answer Figure 1 of 1 Provide Feedback Next > M O Pearson