In this part of the experiment, you will investigate the physical parameters that have an effect on the resistance of a conductor. The conductors to be used are given as in the following. Brass (0.00203 cm") Brass (0.00519 cm³) Brass (0.00811 cm²) Brass (0.0127 cm") Copper (0.00811 cm³) Aluminum (0.00811 cm³) Stainless Steel (0.00811 cm³) Nichrome (0.00811 cm") Part B: Resistance vs Cross-Sectional Area (A): Task: In this part, resistance of four brass wires with different diameters thus cross-sectional areas are to be measured. (I = 1A) Table 2. Resistance of conductor for different cross-sectional areas D (cm) A(cm²) | Length (cm)| I(A) | Voltage (mV) | Resistance (2) 0,1271 0,1016 0,0812 0,0508 0,0127 24 0,00811 0,00519 0,00203 13,6 TA 21,2 33,7 |(A 24 Brass 24 IA 24 89,4 Question: How did the resistance of the conductor change with respect to cross-sectional area? Did the change occur as you have expected? Your Answer: Task (Plot): Resistance vs Cross sectional area (A) graph. (Independent variable A on x-axis, dependent variable R on y-axis)

In this part of the experiment, you will investigate the physical parameters that have an effect on the resistance of a conductor. The conductors to be used are given as in the following. Brass (0.00203 cm") Brass (0.00519 cm³) Brass (0.00811 cm²) Brass (0.0127 cm") Copper (0.00811 cm³) Aluminum (0.00811 cm³) Stainless Steel (0.00811 cm³) Nichrome (0.00811 cm") Part B: Resistance vs Cross-Sectional Area (A): Task: In this part, resistance of four brass wires with different diameters thus cross-sectional areas are to be measured. (I = 1A) Table 2. Resistance of conductor for different cross-sectional areas D (cm) A(cm²) | Length (cm)| I(A) | Voltage (mV) | Resistance (2) 0,1271 0,1016 0,0812 0,0508 0,0127 24 0,00811 0,00519 0,00203 13,6 TA 21,2 33,7 |(A 24 Brass 24 IA 24 89,4 Question: How did the resistance of the conductor change with respect to cross-sectional area? Did the change occur as you have expected? Your Answer: Task (Plot): Resistance vs Cross sectional area (A) graph. (Independent variable A on x-axis, dependent variable R on y-axis)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Note: Please do not handwritten.
A room measures 4mx5mx5m and the air in it has to be always kept 20 C0 lower than that of the incoming air. The air inside has to be renewed every 30 minutes. Take specific heat of air as 0.24 and its density as 1.27 kg/m3. Assuming 75% efficiency, calculate the HP rating of an air-conditioning unit suitable for this purpose. The HP rating is close to _______. which is the correct answer? 2.5 HP 3.5 HP 3.0 HP 1.5 HP
Need help steps would be helpful please and thank you!
Discuss the difference between the off-line and online UPS
What is meant by Electric Bid Package?
A protective put can be used for risk management. A. TRUE B. FALSE
In an electrical system, each of the service entrance conductors has an area of 750 kcmil. The size of analuminum grounding conductor that will be brought to the service should beA. 250 kcmil.B. 4/0.C. 2/0.D. 500 kcmil
what is the receptacle load (after demand factors) for an office building with 250 receptacle outlets ? Explain
Could you answer this question in details and giving examples if possible. Thanks a lot. - Explain what is CAN BUS. This question is related with the Embedded system ( Electrical electronic engineering)
Write the complete specifications of Ceiling Rose.
schedules are typically provided to detail the circuits and overcurrent protection required for listribution equipment. Branch-circuit - Outlet C. d. ore distribution points for electrical in .... Switch Panelboard
Correct and detailed answer will be Upvoted else downvoted. Thank you!