Answered: In the wheelbarrrow, the load has a… | bartleby

Related questions

Question

In the wheelbarrrow, the load has a perpendicular lever arm of 7.5 cm, while the hands have a perpendicular lever arm of 1.02m. (a) what upward force must you exert to support the whellbarrow and its load if their combined mass is 45kg? (b) what force does the wheelbarrow exert on the ground?

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A horizontal wire holds a solid uniform ball of mass (m) in place on a tilted ramp that rises 35.0° above the horizontal. ihe Surface of this ramp is perfectly smooth, and the wire is directed anay from the cen ter of the ball. (3.) What is the tension in the nire? 35.0°
The figure below shows a claw hammer being used to pull a nail out of a horizontal board where 0 = 25.6°. The mass of the hammer is 1.00 kg. A force of 145 N is exerted horizontally as shown, and the nail does not yet move relative to the board. Assume the force the hammer exerts on the nail is parallel to the nail. Ө 30.0 cm Single point of contact 5.00 cm (a) Find the force exerted by the hammer claws on the nail. magnitude KN direction above the horizontal (b) Find the force exerted by the surface on the point of contact with the hammer head. Ĵ) N ( Î +
An 75-kg diver stands at the edge of a 52 kg diving board that is 5.0 meters long, which is supported by two vertical pillars that are 1.6 meters apart, as shown in the figure. Find the magnitude and direction of the force exerted by each pillar. (Only enter magnitude of the left support here but show both the right and left in your work.) 5.0 m 1.6 m
To strengthen his arm and chest muscles, a 79-kg athlete 2.0 m tall is doing a series of push-ups as shown in the figure below (Eigure 1). His center of mass is 1.15 m from the bottom of his feet, and the centers of his palms are 30.0 cm from the top of his head. Figure -2.0m 1 of 1 30.0 cm Find the force that the floor exerts on each of his feet, assuming that both feet exert the same force. Express your answer in newtons. F= Submit Part B F= [5] ΑΣΦ Submit Request Answer Find the force that the floor exerts on each of his hands, assuming both palms exert the same force. Express your answer in newtons. 1971 ΑΣΦ Request Answer ? N N
When you lift an object by moving only your forearm, the main lifting muscle in your arm is the biceps. Suppose the mass of a forearm with hand is 1.60 kg. If the biceps is connected to the forearm a distance of 2.4 cm from the elbow, how much force must the biceps exert to hold a 42 N ball at the end of the forearm at distance of 36.0 cm from the elbow, with the forearm parallel to the floor, in Newtons? Use g = 10.0 m/s2. Your answer needs to have 3 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.
Determine the reaction at the smooth wall. The top of the 15kg ladder is leaning against a very smooth wall. Assume that the mass cebter of the painter is directly above his feet and that the coefficient of friction between the horizontal ground and the ladder is 0.25.
A student creates a beam bridge for a project, suspends masses from the bridge, and spans the bridge across two surfaces, as pictured below. What is the best approximation for the normal force applied on the bridge’s surface from PylonA? (A)About 0.8N (B)About 1.2N (C)About 1.4N (D)About 2.0N
MY NOTES ASK YOU Consider the figure below. (Let w, = 130 N and w, = 55.0 N.) W, W2 (a) What is the minimum force of friction required to hold the system of the figure above in equilibrium? (b) What coefficient of static friction between the 130-N block and the table ensures equilibrium? (Enter the minimum acceptable coefficient of friction.) (c) If the coefficient of kinetic friction between the 130-N block and the table is 0.212, what hanging weight should replace the 55.0-N weight to allow the system to mc constant speed once it is set in motion?
A uniform drawbridge must be held at a 37° angle abovethe horizontal to allow ships to pass underneath. The drawbridge weighs45,000 N and is 14.0 m long. A cable is connected 3.5 m from thehinge where the bridge pivots (measured along the bridge) and pullshorizontally on the bridge to hold it in place. What is the tension in the cable?
A 129N tightrope walker stands at the center of the rope such that each half of the rope makes an angle of 5 degrees with the horizontal. What is the tension in the rope?
A hungry bear weighing 735 N walks out on a beam in an attempt to retrieve a basket of goodies hanging at the end of the beam (see the figure below). The beam is uniform, weighs 200 N, and is 5.50 m long, and it is supported by a wire at an angle of e = 60.0°. The basket weighs 80.0 N. Goodies (a) Draw a force diagram for the beam. (Submit a file with a maximum size of 1 MB.) Choose File No file chosen This answer has not been graded yet. (b) When the bear is at x = 1.20 m, find the tension in the wire supporting the beam. When the bear is at x = 1.20 m, find the components of the force exerted by the wall on the left end of the beam. (Assume the positive +x direction is to the right and the positive +y direction is upward. Include the sign of the value in your answer.) F = (c) If the wire can withstand a maximum tension of 875 N, what is the maximum distance the bear can walk before the wire breaks?
A shelf bracket is mounted on a vertical wall by a single screw. S S2 S1 Neglecting the weight of the bracket, and if s = 6.4 cm, s1 the horizontal force component exerted on the bracket by the screw when a 95.2 N vertical force is applied as shown. Imagine that the bracket is slightly loose. 5.4 cm and s2 = 2.2 cm, find =

SEE MORE QUESTIONS