In the system given in the figure, the rods are identical and it is desired to be produced in the same diameter. The strength of the material to be used is 140N / mm ^2. Find out what the maximum diameter of the bar number 1 and 2 should be.

In the system given in the figure, the rods are identical and it is desired to be produced in the same diameter. The strength of the material to be used is 140N / mm ^2. Find out what the maximum diameter of the bar number 1 and 2 should be.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.18P

See similar textbooks

Related questions

Q: answer should have been 4.78 micrometres, which is option C

A: Given Data: Tensile Stress σc = 89 Mpa = 89×106 Pa Modulus of Elasticity E = 85 GPa =85×109 Pa γs =…

Q: When pouring liquid into a glass, the liquid exerts pressure in which direction?

A: The force imposed on a surface by the air above it as gravity draws it to Earth is known as…

Q: What Law can be verified using the Force Table experiment? 1-Newton's 2nd Law of motion 2-Newton's…

A: The force table method is used to determine the equilibrant forces of one or more known forces and…

Q: 6. An object whose weight is 100 lbf experiences a decrease in kinetic energy of 500 ft. lbf and an…

Q: Choose correct answer: Newton’s third law of motion explains the two forces namely ‘action’ and…

Q: The weight of one dozen apples is 4.6 lb. Determine the average mass of one apple in both SI and US…

A: A rule of thumb is a practical and approximate way of doing or measuring something, based on…

Q: Engineering applications of vapor pressure.

Q: A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will…

A: Given data, Gas pressure, P = 360 MPa Maximum permissible force, F = 9.50 MN = 9.50 x106 N To…

Q: When a particle is subjected to both gravitational and elastic forces, the resultant force is…

A: Assume the mass of the particle m with the displacement x. The expression for the gravitational…

Q: Why is it a good idea to bend you legs as you land on the ground after jumping down from a ledge…

A: We bend the legs during jumping down on the ground from a ledge. The reason behind this is given as…

Question

100%

Help,please

In the system given in the figure, the rods are
identical and it is desired to be produced in
the same diameter. The strength of the
material to be used is 140N/ mm ^2. Find
out what the maximum diameter of the bar
number 1 and 2 should be.
1,2 m
0,5 m
(1)
F=20 kN
-0,9 m 1,2 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem for sx= 11 MPa and ??y= -20 MPa (see figure).
L,=40mm; L,= 120mm; L=100mm and 0,=65°. Find the possible value of 0, and 0, L,=80mm and 3.
Can someone help me to my activity to understand this. Thank you!! :))
A rectangular steel block is 3 inches long in the x direction, 2 inches long in y-direction and 4 inches long in the z direction. The black is subjected to a triaxial loading of three uniformly distributed forces as follow: 30 kips compression in the x direction, 60kips compression in the y-direction and 54 kips in Z direction. If v= 0.45 and E= 29×10⁶ psi find the uniformly distributed load that must be added in the x direction to produce no deformation in the y- direction. The initial strain along x direction. The initial strain along y direction. The initial strain in z direction Additional loading alone x so that Ey=0
As the electric motor rotates at a constant speed, a torque of 500nm is applied to the ABCD shaft. When G = 27 GPa and the torques shown in the figure are applied to the B and C pulleys, what is B and C torsion.
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section
Kindly answer correctly. Please show the necessary steos. Thanks in advance
60mm 2. H we measure a &=13µm decrease in the bolt diameter d. Bolt material properties are given as G=77 GPa and v=0.3. The bolt in the following figure when tightened, Determine the internal force at the bolt due to bolt tightening. i. 1 09 = p
1. A circular shaft with a keyway can be approximated by the section shown in Fig. r=b Ay r r=2acose Figure 1: Circular shaft with a keyway. The keyway is represented by the boundary equation r = b and the shaft is represented by the boundary equation r = 2a cos 0. Show that using a Prandtl stress function of the form ²) (₁ (1-2a cos) X v = K (b² − ²) (1 – : will solve the problem of torsion on this shaft and find the constant K (assume an applied torque T). Compute the shear stress components Txz and Tyz. (Hint: start by converting the stress function to Cartesian coordinates).
Q4
The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Suppose that a= 640 mm
3) For the given plate subjected to two point forces, calculate the nodal displacements and the moments at points A and B. (Note that A is the mid-point of the finite element) E = 30000 MPa h = 0.14 m v = 0.20 2 m 2 m 50 kN 2 m 50 kN A B 50 kN 50 kN 2 m 50 Cross-section along the symmetry axis