in the picture. The engine block assembly weighs 500 lbs. If the unbalanced force produced by the engine is given by 200 sin 100 t lb, design three shock mounts (each stiffness k and viscous damping constant c) such that the vibration amplitude

in the picture. The engine block assembly weighs 500 lbs. If the unbalanced force produced by the engine is given by 200 sin 100 t lb, design three shock mounts (each stiffness k and viscous damping constant c) such that the vibration amplitude

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I Review Use a block-and-spring model like that shown in the figure, but suspended from a vertical position and subjected to a periodic support displacement 8 = 8psinwnt, determine Express your answer as an equation in terms of some or all of the variables y, a (a = y), ki, m, wn (wn = V). wn, t, and on. the equation of motion for the system, and obtain its general solution. Assume positive displacement is downward. (Figure 1) Va AZo| t vec k la+ m k sin @, t m That's not quite right. Please check your formatting and try again. No credit lost. Try again. Submit Previous Answers Request Answer Part B Obtain the general solution of the above equation. Figure 1 of 1 Express your answer in terms of some or all of the variables A, B, t, k, m, wn (Wn = 1/), 80, and wo. V ΑΣφ vec Equilibrium position A sin (@,1) +B cos (@,1) sin (@,) mw,“ 1- k y = Bd8 = 8, sin d Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining
The flexible footbridge shown spans shark infested waters. Humans are expected to walk across the bridge and shake it with a harmonic force of 250 N at a rate of 2 Hz. A tuned vibration absorber is hung from the bridge to mitigate steady-state vibrations of the bridge. The spring stiffness is ka is 1000 N/m. What value is needed for the absorber mass ma? ma
k 0.5m- 1m The moveable mass is removed, the spring stiffness increased to k= 500 N/m and a viscous damper is added to the system. The new system is show in the figure above. The mass of the slender rod remains 6 kg. For what value of the damping coefficient C will the system be critically damped? (round your answer to the nearest whole number) A Ns/m
Figure below shows a rod with mass M = 100 kg, cross section area A = 10 cm². The rod is supported by 4 springs having stiffnesses of k = 1 MN/m. A tip mass with m = 120 kg is attached to the rod. Assume x is the degree of freedom of the equivalent system. The Young's modulus, E, is not known. If the natural frequency of the equivalent mass-spring system is 40 Hz, determine the Young's modulus, E. Assume the length of the rod is L = 5 m. Find the nearest answer. k ww E, A, M k F @www.ww wint L 195 GPa 179 GPa 116 GPa 45 GPa 236 GPa 000 00
An underdamped shock absorber is to be designed for a motor cycle of mass 200 kg(m). When the shock absorber is subjected to an initial vertical velocity due to a road bump, the resulting displacement-time curve is to be as indicated below. Find the necessary stiffness and damping constants of the shock absorber if the damped period of vibration is to be 10 sec(τd) and the amplitude x1is to be reduced to one-eighth in one half cycle. Example is attached
As illustrated in the figure below, the bedplate of an experimental diesel engine is supported on four springs to isolate the vibrations from the test frame. The effective weight of the diesel engine and bedplate is 43kg and the stiffness of each of the four springs is 250 kN/m. Using a simplified approach - by applying Newton's Second Law assuming a single degree of freedom system and ignoring damping - what rotational engine speed is best avoided? Bedplate Test engine Supporting springs Figure: Sketch of a test engine mounting arrangement Give your answer in rad/s to 1 decimal place.
A free vibration of the mechanical system shown in Figure 3 indicates that the to after four consecutive 3. amplitude of vibration decreased to 1/3 of the xo value at t = cycles of motion (i.e. x4 at t = t4). Determine the corresponding spring constant k if m = 15 kg and the viscous friction coefficient b = 4 N-s/m in the system. m Figure 3
The crankshaft-flywheel assembly of a large engine may be considered a torsion pendulum. The shaft is 1.8m long and transmit 179.127kN-m torque corresponding to 83MPa stress. The flywheel diameter is 75cm and weighs 4.5kN. If the modulus of rigidity of the shaft material is 77GPa, compute the period of vibration of this system.
Obtain X1(s)/F(s) and then determine the damping coefficient C of the mechanical system below. m2 =160.1 kg, k =953.7 N/m, k, =1,451.7 N/m, b, =148.0 N-s/m. X1(t) x2(t) k2 f2(t) m2 k, b2 massless plate Sonraki
A free vibration of the mechanical system shown in Figure 3 indicates that the amplitude of vibration decreased to 1/3 of the xo value at t = to after four consecutive cycles of motion (i.e. x4 at t = t4). Determine the corresponding spring constant k if m = 15 kg and the viscous friction coefficient b = 4 N-s/m in the system.
An electric motor of mass 25 kg is supported on a three-spring system. Thesprings are arranged in parallel, with the three stiffnesses being 10 kN/m,5 kN/m and 25 kN/m respectively. Viscous damping is present within the systemand has a magnitude of 0.4 kNs/m.i) Produce a sketch of the system and state its equation of motion.ii) Determine the damping ratio and comment on its value.iii) Determine the amplitude of vibration of the motor 5 cycles afterit is released from an initial displacement of 15 mm.
A rigid block of mass ? is mounted on four elastic supports, as shown in the figure. A mass ? drops from a height ? and adheres to the rigid block without rebounding. If the spring constant of each elastic support is ?, derive the equation of motion and find the natural frequency of vibration of the system (a) without the mass ?, and (b) with the mass ?. Also, find the resulting motion of the system in case (b). By using lagrange energy method