In the given figure, the wires AB and CD made of the same material are used to suspend a rigid block to which the gradual load 'W is applied in such a way that both the wires get stretched by the same amount. If stresses in wires AB and CD are o, and o respectively, then the ratio 1 will be 02 CRIS с T 3 m B A (0₁) W (02) D 6 m

In the given figure, the wires AB and CD made of the same material are used to suspend a rigid block to which the gradual load 'W is applied in such a way that both the wires get stretched by the same amount. If stresses in wires AB and CD are o, and o respectively, then the ratio 1 will be 02 CRIS с T 3 m B A (0₁) W (02) D 6 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bar is shown in figure below: 200 kN 50 mm Id mm 50 mm 200 kN Lmm- Lmm Lmm 500 mm The bar is subjected to a tensile force of 200 kN at each end. The stress in the middle portion is limited to 150 N/mm². If the total elongation of the bar is limited to 0.30 mm, then the value of (L1 + L2) will be [Take E= 200 kN/mm²]
184 What is the strain energy of the massless stepped bar as shown in the figure below? [Take E= 200 GPa] (a) 0.38 N-m (c) 0.50 N-m 30 mm 10 mm 100 mm 20 mm 120 mm • ** ** 80 mm 10 kN (b) 0.42 N-m (d) 0.56 N-m
roblem 2: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, is heated and shrunk onto a steel cylinder 1500.5 mm in diameter. What is the nor- mal force in the hoop after it has cooled? Neglect the deformation of the cylinder, and use E == 200 GPa for steel. roblem 3: The timber member has a cross-sectional area of 1750 mm² and its modulus of elasticity is 12 GPa. Compute the change in the total length of the member after the loads shown are applied. 40 kN 35 kN 20 kN D• A
1) The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping force in each bolt is 4000N, determine the normal strain in the bolts. Each bolt has a diameter of 5 mm. If o₂ = 280 MPa and Est = 210GPa, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released? a) 0.970 b) 0.203 c) 0.970(10-³) d) Insufficient information to determine because the stress is beyond yield point H &
Answer in two decimal places please
Three aluminum rods support the rigid L-shaped bracket BCF as shown in the figure. Determine the stress in rod DE (express answer in MPa) if rod FG is cooled by 50°C. All three rods have the same cross-sectional area of 1000 mm^2. Use 73.1 GPa and 23 x 10^-6/°C for the modulus of elasticity and the coefficient of thermal expansion of aluminum, respectively.
Please Help me
Answer in two decimal places please
Three aluminum rods support the rigid L-shaped bracket BCF as shown in the figure. Determine the stress in rod DE (express answer in MPa) if rod FG is cooled by 50°C. All three rods have the same cross-sectional area of 1000 mm^2. Use 73.1 GPa and 23 x 10^-6 /°C for the modulus of elasticity and the coefficient of thermal expansion of aluminum, respectively.
When laying tracks for the railroad, a small gap & is left between the ends of the rails for thermal expansion. The gap is such that if the temperature increases from -20°F to 90°F the rails will just touch. If the temperature is increased to 110°F, what will be the axial force in the rail with a length L=50 ft, modulus of elasticity E=29x10ʻ psi, coefficient of thermal expansion a=6.6x106/°F, and a cross-sectional area of 5.2 in?. -8 -L ft