In the given figure below, it is required to estimate the Masonry, Plaster, and Rebar quantities and material requirements. a) What is the number of 4" thk. CHB required for the specified wall? (no increase factor to be applied to this number) b) How many cubic meters of mortar for core fill and block laying are required for the wall given that a 1:3 mix will be used? (no gravel to be incorporated) c) How many cubic meters of plaster are required for the wall's rough plaster? 10.0m- EXTERIOR WALL WALL TO BE ESTIMATED INTERIOR WALL INTERIOR WALL 4.4m - 4.4m NOTES: 1) WALL IS 4" THK. CHB 2) WALL IS 2.5m TALL 3) 10mmø HORIZONTAL RSB @ EVERY 2 LAYERS 4) 10mmø VERTICAL BARS SPACED @ 0.4m 0.c. 5) 1:3 PROPORTION TO BE USED FOR MORTAR 6) ROUGH AND FINE PLASTER TO BE APPLIED ONLY TO INTERIOR WALLS 7) ONLY ROUGH PLASTER TO BE APPLIED TO EXTERIOR WALLS

In the given figure below, it is required to estimate the Masonry, Plaster, and Rebar quantities and material requirements. a) What is the number of 4" thk. CHB required for the specified wall? (no increase factor to be applied to this number) b) How many cubic meters of mortar for core fill and block laying are required for the wall given that a 1:3 mix will be used? (no gravel to be incorporated) c) How many cubic meters of plaster are required for the wall's rough plaster? 10.0m- EXTERIOR WALL WALL TO BE ESTIMATED INTERIOR WALL INTERIOR WALL 4.4m - 4.4m NOTES: 1) WALL IS 4" THK. CHB 2) WALL IS 2.5m TALL 3) 10mmø HORIZONTAL RSB @ EVERY 2 LAYERS 4) 10mmø VERTICAL BARS SPACED @ 0.4m 0.c. 5) 1:3 PROPORTION TO BE USED FOR MORTAR 6) ROUGH AND FINE PLASTER TO BE APPLIED ONLY TO INTERIOR WALLS 7) ONLY ROUGH PLASTER TO BE APPLIED TO EXTERIOR WALLS

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question Draw a graph to show the general relationship between the compressive strength of the concrete and the water-cement ratio for different curing times. Label all axes and curves.
An ASTM indicator of workability when evaluating freshly mixed Portland cement concrete. Choices: - C143 - C187 - C191 - C496
Complete a l-page paper summarizing ASTM C270 and its most important aspect in engineering. Also complete the table below. Mortar mixes: All mortars are specified under ASTM C270 Mortar types are classified into classes N to M, classification is by difference in strength and workability , as the strength decreased the workability increase Hw 1: Complete the following table upon reading the chapter Mortar type Bond strength Workability Use Type N mortar Good Good Exterior or veneers non- load bearing walls, interior load-bearing walls Type S mortar Туре O mortar Туре M mortar
What are the four major factors affecting the bond strength of mortar and why is this important?
Reference Table: Quantity of Cement and Sand for mortar and plaster in Properties: Length of wall (1) = 4.0 m, use 6" thick CHB; Size cubic meter of door: 0.90 m x 2.10 m Length of wall (2) = 5.0 m, use 6" thick CHB; Size of window: 1.50 m x 2.20m TABLE 2-1 QUANTITY OF CEMENT AND SAND FOR MORTAR AND PLASTER IN CUBIC METER Class Moture Cement in Bags 40 kg Sand cu. m. Proportion Length of wall (3) = 4.0 m, use 4" thick CHB 50 kg 1:2 1:3 1:4 1:5 18.0 12.0 9.0 7.5 14.5 9.5 7.0 6.0 1.0 1.0 1.0 1.0 Height of "A" from floor line to bottom of beam = 2.80m Height of "B" from the ground line to floor line Your answer 0.30m Height of "C" from ground line to bottom of CHB = 0.30m Determine the quantity of 6" CHB for walls 1, 2 and 3. Your answer Quantity for cement in 40-kg bag used as core filler and block laying Your answer 5500
1. Why is it important that the concrete masonry units meet certain absorption requirements? 2. What is the mortar made of? What are the functions of the mortar? 3. What is the grout? What is the grout used for? 4. What are the ingredients of the plaster? What is it used for?
a Why is it important that the concrete masonry units meet certain absorption requirements?b. A portion of a normal-weight concrete masonry unit was tested forabsorption and moisture content and produced the following masses:mass of unit as received = 1.95 kgsaturated mass of unit = 2.13 kgoven-dry mass of unit = 1.91 kgimmersed mass of unit = 0.95 kgCalculate the absorption in kg/m3and the moisture content of the unit as a percent of total absorption. Does the absorption meet the ASTM C90 requirement for absorption?
B: calculate mortar for a wall which height is 10 feet, length is about 14 and width 9 inch?
Determine the quantities of materials required per cubic yard to create a concrete mix. The specifications require a maximum size aggregate of 1 1/2 in., a minimum cement content of 5 1/2 sacks per cy, and a maximum water-cement ratio of 0.63. Assume 5% air voids.
a Why is it important that the concrete masonry units meet certain absorption requirements? b. A portion of a normal-weight concrete masonry unit was tested for absorption and moisture content and produced the following masses: mass of unit as received = 1.95 kg saturated mass of unit = 2.13 kg oven-dry mass of unit = 1.91 kg immersed mass of unit = 0.95 kg Calculate the absorption in kg/m³ and the moisture content of the unit as a percent of total absorption. Does the absorption meet the ASTM C90 requirement for absorption?