In the following circuit, R1 = 8 Ohms, R2 = 5 Ohms R3 = 2 Ohms and R4 =12 Ohms and Vs = 14 Volts. The Thevenin equivalent of this circuit consists of a voltage source VTh and series resistance RTh. FInd Vth and Rth and hence determine the current that will flow through a 25 2 resistor connected between points A and B. Give your answer as a positive value in Amps to three decimal places. Vs R3 R4 R2 R1 A B V Th RT I B

In the following circuit, R1 = 8 Ohms, R2 = 5 Ohms R3 = 2 Ohms and R4 =12 Ohms and Vs = 14 Volts. The Thevenin equivalent of this circuit consists of a voltage source VTh and series resistance RTh. FInd Vth and Rth and hence determine the current that will flow through a 25 2 resistor connected between points A and B. Give your answer as a positive value in Amps to three decimal places. Vs R3 R4 R2 R1 A B V Th RT I B

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. A voltage divider provides 1 V output from 5 V input. The maximum output current is 1 mA. The resistors are chosen to provide load regulation of better than 1% over the load current range of 0-1 mA. Find the resistor values necessary for this application. What is the efficiency at full load?
This Homework is too much... i already solved 3 question but still alot to go.. Please Help me Solve this.
For the given circuit in Figure below, find the open circuit voltage VTH and the short circuit current IN across the terminal. then, find R TH by using the RTH=VTH/IN equation and find RTH with replacing voltage source with short circuit. Let’s assume we connect RL (load resistance) to the circuit between points A and B, what should be the value of RL in order to have max power transfer.
9. When using superposition, what is the ideal internal resistance of a voltage source? The Thevenin equivalent resistance An open circuit O A short circuit The equivalent resistance of the reduced combination circuit.
its not graded as before rejected
I posted the same question but the value are wrong .. please check.. Ans for v2 and v3 should be 1.2500V & -1.2500V.. 1. Construct the circuit as shown in Figure 1. Set VS1 and VS2 to 5 V. Measure each of node voltages and record that results in Table below.R1= 1kR2= 3.3k R3= 2.2kR4= 4.7kR5= 1.2k Table 4.2: Nodal Voltage Values Parameter (Volts) THEORITICAL V1 V2 V3 V4 Please draw the current flow in arrow in the circuit. Tq
Consider the circuit diagram below. Solve for the voltage at node b and thecurrent through R5 using node analysis. You can use CircuitJS to verify yourresult, but you are not required to.
Use node analysis to find V1 in the circuit in figure. Could you please do the solution with both simulation and formula (Thank you very much)
Solve the circuit in Figure Q2(b) at terminal a-b using Thevenin's Theorem. iii) Interpret the Thevenin equivalent circuit.
The image contains the problems that need to be solved. This is a voltage divider circuit, and it is understood that V0 is maximized when one of the resistors is at its maximum value while the other is at its minimum (and vice versa for the minimum V0). The answers are provided, but the process is needed.
GET THE CURRENT IN V2
The circuit in the figure is connected to a voltage source U.When S is in the off position, the current I = 6 A and R = 45.a) How large is the total replacement resistance of the circuit.The power switch is turned on. The voltage U remains unchanged.b) How big will you be when S is on.c) How large will the circuit's replacement resistance be now.d) What effect is developing in the circuit now