In the Figure.Q3, The energy decline of the connections and the pipe before the pump is 3m. (Patm=105 Pa and Py=4X104 Pa) 4 m 7 m PUMP

Q: For an 80 gpm pump, what should be the approximate size of the reservoir to ensure sufficient oil…

A: Given data:- pump capacity =80GPM To find:-the approximate size of the reservoir

Q: Write notes with sketch on (i) Gear pump (ii) Peristaltic pump.

A: Gear pump:  A gear pump uses the meshing of gears to pump fluid by displacement. They are one of…

Q: How high must the pump centerline be located above the water level in an open tank that supplies…

A:

Q: While calculating the Wnet it is nessesary to reduse the pump work i think, can you fix this please

A: The inlet pressure at the turbine P3 =P2 =10 MPa  The inlet temperature at the turbine T3= 350 °C…

Q: What is the principle of centerifugal pump?

A:

Q: List down the different types of pumps together with its application. Classify them into Positive…

A: There are two types of pump: 1). Rotodynamic pump(Centrifugal pump)or Non-positive displacement pump…

Q: WHAT HP (CENTRIFUGAL FAN) IS NEEDED TO SUPPLY AIR MOVING AT 20 FEET PER MINUTE (FPM) THROUGH A 2X3…

A: Given data: v=20 ft/mA=2×3 ft2hw=3 in Need to determine the power required for the fan.

Q: two suggestions in reducing the head loss in the pump and piping syste

A: -Make the surface of the pipe is smooth so that no friction is present in the piping system so this…

Q: Venn Diagram of the difference between actual and theoretical discharge

A: To show the difference between actual discharge and theoretical discharge

Q: The main purpose for hydraulic fluids is:

A: The main purpose for hydraulic fluids is:  1) To transfer the energy from input point to output…

Q: . Omar Juma is working in shaping machine of a gear manufacturing company. This shaping machine ram…

A: Given Data→ Shaping machine of a gear manufacturing company

Q: Draw how it look if it is a laminar flow in pipe.

A:

Q: If the net positive suction head (NPSH) is greater than the required suction head of the pump,…

A: If NPSH (net positive suction head) available is greater than the NPSH required than cavitation will…

Q: Discuss the relation between the head pressure and flow rate for the benefits of connecting the…

A: Solution:

Q: The vena contracta is the section where this minimum flow area occurs in a sudden contraction

A:

Q: Explain major impact all major losses through the pipes.

A:

Q: Define aur vessels. Explain the advantages of air vessel in pump system.

A: Air vessels are used in the reciprocating pump. It is basically a cast iron closed chamber having an…

Q: What type of pump would you recommend if the capacity is 200 gal/min at a head of 600ft of water

A:

Q: If the net positive suction head (NPSH) requirement for the pump is not satisfied, then_ Select one:…

A: NPSH is the property of the pump and it is defined as the difference between the available NPSH at…

Q: Power operated pump in which only one side engages the fluid displacement is called.

A: Correct option is:

Q: SUGGEST ATLEAST 4 WAYS TO INCREASE TO THE AVAILABLE NET POSITIVE SUCTION HEAD (NPSH)

A: Given Data- In question Fluid mechanics phenomenon NPSH given we have to list 4 ways by which we can…

Q: Choose correct answer: Pump converts ___________ A. Mechanical energy to Hydraulic energy B.…

A: Pump converts the Mechanical energy into hydraulic energy of the liquid.

Q: At the lowest points of a pipe there should be drains and while at the highest points there should…

A: The objective of the question is to understand the reason behind the placement of drains at the…

Q: What type of pump is shown in Fig. ? How does itoperate?

A: This is a flexible liner pump

Q: What is the impact on flow and pressure when the impeller of a pump is trimmed? a. Flow decreases…

A:

Q: state the affinity laws applicable to centrifugal pumps

A: The affinity laws application to centrifugal pumps are explained as follows.

Q: 'What type of lizard pump belongs to and why? Explain that through laws?

A: Lizards use Buccal pumping technique. Buccal pumping is "breathing with one's cheeks": a method of…

Q: How to a fule pump transfers mechanical energy to a fluid by raising its pressure.

A: A pump is a device which converts mechanical energy into pressure energy

Q: Explain the operating system for the following pumps and for each explain when they would be used as…

A: It is asked to write the operating system for the single and two stage pump and explain the reason…

Q: revolving buoy.  a. venturi meter b. orifice c. pitot tube  d. rotameter

A: Rotameter is used to calculate the revolving buoy

Q: Please list the symbols for pumps, actuators and different kinds of pressure valves.

A: The symbols for pumps, actuators and different kinds of pressure valves.

Q: Why cavitation in pumps need to be avoid from occuring

A: Cavitation is the rapid process of formation and collapse of vapor bubbles in a liquid. In a pump,…

Q: In order to measure the flow with a Venturimeter, it is installed in Horizontal line inclined line…

A: Venturimeter is a device that used to measure the flow rate of the fluid, it is installed in any…

Q: Why do positive displacement pumps cause pose more overpressure hazard compared with centrifugal…

A: The reason for positive displacement pumps being more hazardous is the range of compression. The…

Q: Primary pump fill the tank in 2hrs.Secondary pump fill the tank in 4 hrs.The 2 pump is connected in…

A: To find: The time to fill the tank. Given: The tank is filled by primary pump is 2 hrs. The tank is…

Q: Does Mary have a valid concern about the pump?

A: You have asked, does Mary have a valid concern about the Pump.

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.