In the figure, two blocks are connected over a pulley. The mass of block A is 6.70 kg and the coefficient of kinetic friction between A and the incline is 0.160. Angle 8 of the incline is 46.0°. Block A slides down the incline at constant speed. What is the mass of block B? Frictionless, massless pulley B Number Units

In the figure, two blocks are connected over a pulley. The mass of block A is 6.70 kg and the coefficient of kinetic friction between A and the incline is 0.160. Angle 8 of the incline is 46.0°. Block A slides down the incline at constant speed. What is the mass of block B? Frictionless, massless pulley B Number Units

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Yi.A 89 uare Pooting of ix mis Loca ted of Ixl M M ig Loc ceted at ** a deP th 1-5m below the ground Surfacs The 8oil properties are: :c'-0 ,Ø= 40,8=16.7ka %3D Ysat= 20 XNlm3, U8mg meyerhofs bearmg capacity %3D equa tions calculats the uItimaate bearing Capacity a) The water table ig well below The foun dation Level b) The Water table is at The growmd Sur face
11. Which IS codes gives details about elevators? A. O IS 27752 B. O IS 38665 C. O IS 14665 D. O IS 27855
answer question a)
Complete the following set of profile level notes to answer questions [Select] [Select] [ Select] Station BS BM1 2.565 1+100 1+200 TP1 1+300 1+400 1+500 HI FS IFS TP2 1.946 ? 1.946 BM2 ? 33.562 3.741 1.768 2.543 The HI at TP1 is 1.154 0.752 3.051 Elevation (m) 32.756 ? 31.500 30.429 The elevation at station 1+100 is The backsight reading at TP1 is
Use Factor method in solving this problem. Details are already provided in the drawing
13 19 81 30 33 3 27 90 5.5 3. 8. 89 69 土1 pom the water furface whereas the 18 24 The deptt usas measured a velociky wap measured woith a prpellv within egch define Creso Sectionof the nver. The efechicead Vefocefies within each panel Cross sectrion and theis Corsespending depths ane shown 'in the table above : 9. Compute the average kpfh and velocity within en ch Panel billsing the single point methsd, Calufate the meas velocubly et the flow wlthin each panel Cross section c. Ufing ether the meay secfion miel-sectisn mgeths Catulhte the avevage elis charge withew each panel Cross section amed thus the toal escharge of the riyen Cros Seefion a depth (ycoed
Kindly verify if I am correct. I think the book had an error with the x component of the centroid of the angle bars that is why we got different answers
Please help me solve the question in the picture below
ASAP
PROBLEM 1: Consider the force system shown with the following forces and given angles: F1 = 83 kN F2 = 35 KN F3 = 83 kN 01 = 16⁰ 02 = 12⁰ 03 = 22⁰ 04 = 40⁰ NOT TO BE UPLOADED OR SHARED ANY TUTORIAL SITES OR GROUPS 2.0= USTE ENGRAS AY2223 SHARED U NOT TO BE UPLOADED OR ANY TUTORIAL SITES OR ROUPS UST CE EN18 AY2223 A NOT TO BUPADED OR SHARED T TUTORIAL SITES OR GROUPS UST CE EN 2018 AY2223 0₁ F₁ NOT TO BE UPLOADED OR SHARED TO ANY TUTORIAL SITES OR GROUPS UST CE ENG2018 AY2223 0₂ X 03 04 F₂ DO NOT INCLUDE NEGATIVE SIGNS IN YOUR ANSWERS • Calculate the magnitude and direction of resultant with respect to the x-axis. 1. R= KN use 2 decimal places use 3 decimal places • Calculate the moment of the force system about point A, if L = 3.3 m. 3. M = kN-m use 3 decimal places F3
Find VC, NC, MC
I need the answer as soon as possible