In the figure below the input stimulus and its corresponding output response is plotted . It is seen that the same result was not obtained while performing the measurement under the same condition at different times (run 1 and run 2). Give possible reasons why the same reading for run 1 and run 2 is not achieved and comment on the sensors repeatability and response time. | output run 1 run 2

In the figure below the input stimulus and its corresponding output response is plotted . It is seen that the same result was not obtained while performing the measurement under the same condition at different times (run 1 and run 2). Give possible reasons why the same reading for run 1 and run 2 is not achieved and comment on the sensors repeatability and response time. | output run 1 run 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question No. 2a. In an Experiment, a high speed diode is to be used. The experimentalist has the liberty to make the diode with Si, Ge or GaAs. Which one would you prefer and why? b. Design a circuit for 5V DC from 12 V DC. Explain your circuit. c. Figure ‘a’ represents the input signal to a circuit which gives the output as the waveform ‘b’. Design the circuit and explain the working in detail
Design a +40 volt dc power supply for your sound system. Your sound system requires a 400 watt capability. The power supply is energized from a three-wire 110 Vrms 60 Hz power line that meets the National Electric Code (NEC). The system block diagram and design specifications are given below. Input is a 110 Vrms60 Hz. Output voltage is 40 volts, unregulated. Maximum allowable ripple is 2% Use a full-wave bridge rectifier. Use a transformer Assume diodes with VF= 0.7 volts Your design should include: Ø Well-labeled circuit diagram of what goes in the “Your Design” box. There should be enough detail such that someone could build an operational prototype. Polarities of key components are important Ø Key design equations and supporting calculations. Show your work! Ø Component specifications including: (a) Transformer-turns ratio (b) Effective value of the audio system load resistor (speaker impedance) and load current for a 400 watt, 40 volt…
A) Choose the correct answer. 1) For purposes of measuring length, the human torso was a convenient tool, and gave us units of----------? A) Meter. B) cm. C) foot. D) mm. 2)--------he output signal consists of a proportion of the external voltage source applied across the two ends of the potentiometer. A) Null-type, B) deflection-type C) passive instrument „D) active instrument. 3) The prerequisite for the reduction of systematic errors is a complete analysis of the---? A) Measurement system, B) systematic errors, C) System disturbance, D) Errors. 4) The extent to which series mode noise cornunts measurement signals is measured bv a
build an inverting summing amplifier with 2 inputs: a 1 V DC signal anda sine wave with an amplitude of 2 V and 1 kHz frequency.V Simulate for 2 msec
V4
Please answer in typing format
I need the answer quickly
Please answer clearly
instruction: answer item 4, 6, and 7 4. Mancio Manufacturing Co. has asked you, as their IE, to check a labor standard prepared by arecently resigned analyst. Determine the sample size you need considering your accuracy is to bewithin 5%, standard deviation of the sample is 1.0 and the mean is 3.0. 6. At ASP Micro Manufacturing, Inc. workers press semiconductor into predrilled slots on printed-circuit boards. Determine the normal time of the operation in seconds. The elemental motions for normal time used by the company are as follows:• Reach 6 inches for semiconductors 10.5 TMU• Grasp the semiconductors 8.0 TMU• Move semiconductor to printed-circuit board 9.5 TMU• Position semiconductor 20.1 TMU• Press semiconductor into slots 20.3 TMU• Move board aside 15.8 TMU 7. The semiconductor used in Costin Calculator has 5 components with the consistency of 90%, 95%,98%, 90%, and 99%, respectively. How reliable is one product of calculator?
Assuming that output Q=0 initially (before point A), apply the waveforms x and y shown in the figure to inputs S and R, respectively, of an SR NOR Latch.Question: What is the value of output Q' at point G?a. lowb. highc. indeterminated. transitioning from low to highe. transitioning from high to low
Question 3 The 555 timer is connected in the following circuit. The resistance of the extra resistor is 102, the capacitance of the extra capacitor is 0.1F. The voltage input at Pin2 is Vcc. What is the output state at Pin3? 1) 2) Decide the voltage input value at Pin 6 when the condition is stable. 3) Decide the output state at Pin3 when a trigger input is applied at Pin2 (voltage input at Pin2 changes from Vcc to 0, and return back to Vcc immediately). 4) After the trigger input is applied at Pin2, how long would the output maintain at the unstable state. Vc R O Output Vo 555 Vc 0.01µF Trigger Input
Describe at least two methods of checking the operation of hall effect sensors in car.(Automotive industry)