Answered: In the figure below, find the resultant…

Engineering

Mechanical Engineering

In the figure below, find the resultant of the two forces and a direction

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.55P: The force R is the resultant of P and 0. Determine Q and the angle .

See similar textbooks

Related questions

Q: | نقطتان )2( -- drink lot of water because l .am thirsty must have to

A: I have to drink a lot of water because I am thirsty here we need to use have to instead of must

Q: Q6/ A Proell governor has arms of 305 mm length. The upper arms are hinged on the axis of rotation,…

A: A governor is used to maintain a mean speed of an engine under varying loads by altering the fuel…

Q: Air flows in the duct shown in Figure. The first shock, which turns the flow 15°, is observed to…

Q: In each case, express the shear and moment functions in terms of x, and then draw the shear and…

Q: 1.1) Consider the air in an Otto cycle with e = 0.48. At the start of the adiabatic compression P =…

Q: Circular fins of uniform cross section, with diameter of 10 mm and length of 50 mm, are attached to…

Q: Consider a steam power plant that operates on an ideal reheat- regenerative Rankine cycle with one…

Q: Q3: A: A half circle of area made from wood, while the other half made from metal. Can you consider…

A: Centroid :- It is the location where entire Volume or Area (for 2D) of the object is concentrate.…

Q: Q1// An element in the boiler is triaxially stressed, the stresses distribution is given by (see…

Q: An air conditioning system is to be designed for a restaurant with the following data: Outside…

Q: (1) A helicopter gas turbine requires an overall compressor pressure ratio of 12:1. This is to be…

Q: 1.69.Obtain the principal stresses and the related direction cosines for the following cases: 4 6. 4…

A: A)The Principal Stress; I1 = σx+σy+σz = 3 - 2 + 1 = 2 I2 = σxσy+σyσz+σzσx - τxy2 -τyz2-τzx2 =…

Q: One kilogram of air is heated reversibly at * constant pressure from an initial state of 300 K and 1…

Q: Internal energy of R-134a at temperature of 0°C and quality of 60% is

A: Given; Internal energy of R-134a atTemperature (T)=00 CQuality (Q)=60%=0.6

Q: Water flows through the pipe contrac- For the given 0.2-m difference in manometer level, determine…

Q: e top arms make 45° with the axis of rotation in the equilibrium position, find the range of speed…

A: M=mass of contol load=18 kgm=mass of ball =2kgF= friction =14Nh= height of governorcos 45 =h250from…

Q: Q2) A boom 20m long supports a load of 1200 kg as shown in the below figure. The cable BC is…

A: The given load and cable and the FBD is as shown below, T1=mgT1=12009.81T1=11.772 kN

Q: A. Calculate the pressure of vapor at a temperature of 400°C and a density of 20 kg/m using (a) the…

Q: Calculate the gas pressure, of air density is 1.22 Kg/m3, L-200 mm * Patm Gas at pressure p Tank…

A: Given:- L = 200 mm = 0.2 m Air density = 1.22 kg/m3 To Find:- Gas Pressure (P)

Q: Q 1 The pressure in a tank is measured with a manometer by measuring the differential height of the…

A: Given Data The density of the water is : ρ=62.4 lbm/ft3 The specific gravity of the fluid is:…

Q: The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 14 mm2 and…

A: FBD is drawn. Elongation in BC is calculated and subsequently deflection at D is found out.

Q: II. By increasing the spring stiffness, what happens to the static sensitivity, time constant and…

A: Solution ii:-

Q: Part A A fluid of density p and viscosity μ flows at an average velocity v through a circular pipe…

Q: A1.8-m-diameter spherical tank of negligible thickness contains iced water at 0°C. Air at 25°C flows…

Q: Q2) If the motorcycle leaves the ramp traveling at 110 ft/s, determine the height h ramp B must have…

Q: Example 5: A rear engine automobile is travelling along a track of 100 m mean radius. Each of the…

Q: Q8: The 1.5-kg ball is given an initial velocity va = 2.5m/s in the vertical plane at position A,…

Q: of expansion or contraction. And assume constant specific heats of 4.18 2. A steel casting weighting…

Q: q.4 – Consider a steam turbine in which the steam enters as superheated vapor at (800 °K & 6 MPa)…

Q: Young's modulus is defined as the ratio of O Shear stress to shear strain O Longitudinal stress and…

Question

I need the answer quickly

In the figure below, find the resultant of the
two forces and a direction
200 kN
3.
150 kN
4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Resolving forces

VIEW

Final solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

The force R is the resultant of P and 0. Determine Q and the angle .
Given that P=120lb and Q=130lb, find the rectangular representation of P+Q.
Find a unit vector that is perpendicular to both A=4i-3j-2km and B=2i4j+3km.
Find the internal force systems acting on sections 1 and 2.
Find the forces Q1,Q2, and Q3 so that the two forces systems are equivalent.
The magnitude of the force F is 55 lb. Calculate the moment of F about the x-axis using (a) the scalar method; and (b) the vector method.
If the intensity of the line loading is w=[(40xx2)/40]lb/in., where x is measured in inches, use integration to find the resultant.
Determine (a) the angle between the position vectors P and Q; and (b) a unit vector perpendicular to P and Q.
Resolve the 360-lb force into components along the cables AB and AC. Use =60 and =40.
It can be show that a plane area may he represented by a vector A=A, where A is the area and represents a unit vector normal to the piano: of the area. Show that the area vector of the parallelogram formed by the vectors a and b shown in the figure is A=ab.
A circular region of radius R/2 is cut out from the circular region of radius R as shown. For what distance d will kx for the new region be the same as kx (for the region before the cutout was removed?
For the position vectors P and Q shown, determine the orthogonal component of P Ă— Q in the direction of OA.