In the Experiment 3, Open circuit Voltage on Secondary with V, = 220 V, E2 = 230VV, inh inw, inV2 inI2 inW2 inVoltsAmpswattsVoltsAmpswatts2200.922032250.81187Then the value of % Efficiency is,O 87.3%O 80.5%O 85.85%O 92.11%In experiment 4, the tabulation of the open circuit test is given below:V, in VoltsVo in VoltsCosøolo in AmpsWo in watts2202300.250.950The magnetising component current, Im is given by,In experiment 4, the tabulation of the open circuit test is given below:V, in VoltsVo in VoltsKlo in AmpsWo in watts220235?0.950The value of transformation ratio, K =

As per bartleby guideline for more than one question asked only first is to be answered please…

In the Experiment 3, Open circuit Voltage on Secondary with V1 = V, E2 V V, in h in W, in 1z in Amps Vz in W2 in Volts Amps watts Volts watts 220 0.92 203 225 0.81 187 Then the value of % Efficiency is, O 87.3% O 80.5% O 85.85% 92 11%

In the Experiment 3, Open circuit Voltage on Secondary with V1 = V, E2 V V, in h in W, in 1z in Amps Vz in W2 in Volts Amps watts Volts watts 220 0.92 203 225 0.81 187 Then the value of % Efficiency is, O 87.3% O 80.5% O 85.85% 92 11%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In reference to the given figure, VCB = 10.3V and VBE = 0.7V. NOTES: VCB = VC-VB VBE = VB-VE In reference to Figure 1, what will be the ICq, in mA? In reference to Figure 1, what will be the voltage across RB, in volts?
Q. 3. For the circuit show in Figure-3: (a) (b) (c) (d) Determine V, I, Iz and la if R;=180 0. Repeat part (a) if R=470 Determine the value of R, that will establish maximum power conditions for the Zener diode. Determine the minimum value of R, to ensure that the Zener diode is in the "on" state.
For the circuit shown in figure below, find the unknown currents. 50 A 12 100 A 20A 10A 20 A
Plz plz solve within 30min I vill give definitely upvote and vill give positive feedback thank you sir
Q3/ Consider the circuit in Figure (2), answer Three branch only. (a)-What type of circuit is this? (b)-What is the total peak secondary voltage? (c)-Find the peak voltage across each half of the secondary. (d)-Sketch the voltage waveform across RL. 120 Vrms 4:1 mmmm eltee D₁ D₂ RL 1.0 ΚΩ
des istance of given diffesent ial amplifies. missing Find the differential Consideo standasd value if data is IS V B = 100 lot 2 Rs vi 1SO2 ISORÉ RE + RE Vid 20oke R
1) +Vc" 20 V For the circuit in Figure 1, calculate the following with the exact analysis. (Make the solutions for silicon transistors) Re 10 k2 75 kn a) Find VB, Vc, VE, VBE, VCE, VBc for ß = 80 B- 80 b) For ß = 80 and ß =160 , compare the VCE and Ic in a table, show the rate of change with percentages (%). Explain the reason for this result. VE R82 10 k2 RE 1.2 k2 Figure 1
Analyze the output voltage Vo in the network efficiently for sinusoidal input signal Vi shown in Figure 2. Apply ideal diode model for solution. Hint: Show your calculation for each of the positive and negative half cycle and Draw the output voltage with respect to input voltage. X-6, Y =6 D1 Vi (Y+1) V (X+5)V Vo Figure 2
Hw For the cirauit belouw, Find the reading of the Voltmeter. A 152 2o0v 250V Ans: V= 180.669 V
Determine the voltage output from a Wheatstone bridge if four active strain gages are used in an initially balanced bridge to measure a strain of 750 µɛ. Assume that a digital voltmeter (Rin = infinity) will be used to measure the output voltage and that Sg =2.01 and the supply voltage is 10 volts. Assume that each gage resistance is 350 ohms. 14.06 mv 7.538 mv 28.12 mv 15.66 mv 3.246 mv