In the design of a timing mechanism, the motion of pin P in the fixed circular slot is controlled by the guide A, which is being elevated by its lead screw. Guide A starts from rest with pin P at the lowest point in the circular slot, and accelerates upward at a constant rate until it reaches a speed of 130 mm/s at the halfway point of its vertical displacement. The guide then decelerates at a constant rate and comes to a stop with pin P at the uppermost point in the circular slot. Determine the n- and t-components of acceleration of pin P once the pin has traveled 29° around the slot from the starting position. Please solve step by step

Q: TA Problem 2: The electric motor at A drives a flywheel C, which is integrated with a pulley D as…

A:

Q: at the instant shown in Problem, the crankshaft AB has an angular velocity of 2000 rpm in a…

A:

Q: he mechanism below has a crank that revolves clockwise at point O at a speed of 2000 rpm. B 1.2 kg…

A: Angular acceleration and linear acceleration of links need to be evaluated.

Q: Question 5 [3/68]: The spring-mounted 0.8-kg collar A oscillates along the horizontal rod, which is…

A: Introduction:The circular motion of an axis of rotation is known as rotational motion. Circular…

Q: A belt moves between the pulleys of the crankshaft of the air conditioning fan and over the idler…

A:

Q: In the mechanism shown in the Figure Q2(b), the wheel rolls without slipping on the horizontal…

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: The 13.9-in. spring is compressed to a 8.9-in. length, where it is released from rest and…

A: Given Data: Length of spring L=13.9 in=13.912ft=1.158 ft Spring compressed to 8.9 in=8.912ft=0.742…

Q: A connecting rod is supported by a knife-edge at point A. For small oscillations the angular…

A: maximum angular velocity when t = 2sec.

Q: Consider (Figure 1). For a short period of time, the motor turns gear A with a constant angular…

A: Jskak

Q: e In the four-bar linkage system shown, let the circular guide with center at O be fixed such that,…

A: The values are H=3.5 ft, R=2ft, L=3ft, θ=37°, β=25.07°,γ=78.71° The velocity of the collar is Vc=24…

Q: A Scotch yoke is a mechanism that transforms the circular motion of a crank into the reciprocating…

A:

Q: Gear A Radius = 0.06 m    Gear B Radius = 0.3 m       Gear C Radius = 0.36 m Note that the Load is…

A: From the given data,

Q: Consider (Figure 1). For a short period of time, the motor turns gear A with a constant angular…

A: Find the velocity of cylinder and distance travelled by the cylinder in three seconds.

Q: 1. Draw the complete and clear FBD of the block C. Indicate two sides of the FBD with all forces and…

A:

Q: 2. The strings AB and AC connect the 200 g ball to the vertical shaft, as shown in Fig. 2. The shaft…

A:

Q: Q22-23 The three balls each have a mass m. If A has a speed VAI = 5 m/s just before a direct…

A: NOTE: The question number 14 is not available in picture. Si as per the guidelines, I solved first…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: N=600 rpmt=4s

Q: tarting from rest, at the instant shown. the considered disk has an angular acceleration a=9 rad.s²…

A: Given   Angular acceleration = 9 rad/s2                      Radius, r = 0.5 m Find  Acceleration of…

Q: m/s and an acceleration ap At the instant shown, the paper is being unrolled with a speed, vp = 7.5…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.