in the crest gate on a dam shown in the figure,: surface AB form's the arc of a circle.of 6. m. radius subtending 60 at the hinge. The gate is 3 m. long. With water surface at 8, compute the vertical component of tótal pressure on АВ. a) 110 kN b) 125 kN C) 134 kN d) 148 kN 6 m 60 hinge 6 m'.

in the crest gate on a dam shown in the figure,: surface AB form's the arc of a circle.of 6. m. radius subtending 60 at the hinge. The gate is 3 m. long. With water surface at 8, compute the vertical component of tótal pressure on АВ. a) 110 kN b) 125 kN C) 134 kN d) 148 kN 6 m 60 hinge 6 m'.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the quarter circle gate BC with a hinge at C, the force P = ... . kN to hold the gate stationary for 2.4 m wide gate. Let r = 2.9 m %3D .... ... | Tr m Water C
Thnz
7. A vertical rectangular sluice gate at the bottom of the dam is 0.60m wide and 1.8m high and exposed to water pressure on one side corresponding to a head of 15m above its center. Assuming the gate on stem to weigh 2300 N and the coefficient of friction of the gate on runners to be 0.25, find the force necessary to raise it. WA/
1. A conical tank (vertex downward) has a radius of 3 m and a height of 5m. If the tank is half-filled with water, find the work done in pumping the water to a level 2m above the tank. (NOTE: Place the top of the tank along the x-axis) 2. A semicircular gate on a dam has a diameter of 6m and is positioned with the straight portion (diameter) on top. If the surface of the water is level with the top, find the total force against the gate.
Problem 2 Water flows through a horizontal 45 degree bend with a 22-in dimeter at a rate of 20 ft³/s under a pressure of 15 lb/in². a. In the x-direction P₁ b. In the y-direction y κα F *P2, Fx F Neglecting the head loss in the bend, calculate the resisting force required to anchor this pipe bed: X
3. .A2.44m diameter cylinder weighs 227.3 kgf and rest on the bottom of a tank that is 0.91m long. Water and oil poured into the left and right hand portions of the tank depths of 0.61m and 1.22m respectively. Find the magnitude of the horizontal and vertical components of the force that will keep the cylinder touching the tank at B. 4. The profile of a mass concrete dam is parabolic. If the dam retains water to a depth of 60m, find the resultant thrust per meter run of the dam, its inclination to the horizontal and the point where it cuts the horizontal base line.
9. Calculate the flowrate beneath the dam shown and the uplift force per foot of dam. Assume Point A is 40 feet from the front of the structure. K = 2 x 10- 5 cm/sec El = 100' El = 81¹ El = 70' 50'- AT B El = 80' El = 75
Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.12.9517 b.39.5136 c.30.4889 d.99.9358 What gage pressure p1 in kPa, is needed to provide the given flow rate? a.1692 kPa b.1121 kPa c.1328 kPa d.1725 kPa
1.
3. An opening gate was installed in an irrigated land drainage system automatic to avoid flooding, articulated in O and with an angle of 0 = 40° with the horizontal, as shown in the figure. The gate weighs W = 9.0 kN and has a height L = 1.7 m; width w = 1,8 m. a) If the height of water is equal to h = 0.65 m, determine the resulting force of water on the gate and the application point in relation to point O. b) To what height of water h will the gate open? That is, rotate in the anti-schedule. L h
3. A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is-34.465 kPa at A in the suction pipe. The 15 cm diam pipe discharges horizontally into air at C. To what height h above B can the water be raised if B is 1.8 m. above A and 20 hp is delivered to the pump? Assume that the pump operates at 80 % efficiency and that the frictional loss in the pipe between A and C is 3 m. Given: Suction pipe Discharge pipe 1.80 m pump Datum line DA = 20 cm = 0.20 m De = Dc = 15 cm 0.15 m PA=- 34.465 KPa (suction pressure) Ve = Vc = 3.6 m/s Pc 0 (atmospheric pressure) BHP = 20 hp Pump efficiency = 80% HLA-C) = 3 m Required:
The normal depth of flow in a trapezoid channel lined with conmcrete is 20M.The cahnnel bed with b=5m and slides slobe at 1:2 n=0.015 So=0.001 (a) Determine Q, mean Velocity,V and Renolds number Re Find shear force that the water exert on the channel (b) If Q in (a) is halfed fidn the normal depth(Y) (c)Repeat the(a) if the channel was rectangular with the same width 5.om (d)Repeat(b) using a rectangle of b=5m