in the conduit diagram shown in figure 17-3 determine how many wires are in each conduit between each piece of equipment.identify each wire terminal connection and quantity of wires above the disconnect switch

Q: 1. What is mean by sequencly connectión. 2. What is the benefit of using the, connectors (C], C2} in…

A:

Q: A factory need a drive system for a conveyer system. Voltage source available is three phase 415 (a)…

A: a) i) The design of DC drive system is given below,

Q: Which of the following components would not be connected in series with the contactor coil A.…

A: In the commercial condensing unit, compressor is an important part. The compressor contactor control…

Q: 14.a. An encoder is a device that is used to A. excite the motor's interpoles. B. feed pack position…

A:

Q: In 4-point starters the resistance is added in series with NVC because __________________ a) To…

A: At the starting of the motor, Back emf (Eb) will be zero, hence a very high current flows through…

Q: Q2/ Design a 4-pole wave winding for an armature with 21 slots. Assume single turn coils and two…

A: Step 1:  Designing a 4-Pole Wave Winding for a 21-Slot Armature The steps involved in designing a…

Q: A motor starter contains protection devices to prevent an overcurrent condition in the motor's…

A:

Q: Q2. List three differences between a P-type and an N-type semiconductor. (you can use diagram)

A: Semiconductor have their electrical conductivity more than non metal and less than metal

Q: b- Fill in the blanks (Answer Two Only) 1- Give an application of three phase AC voltage controller.…

A:

Q: Elimination of armature reaction requires a series field winding O True False

A: The elimination of armature reaction requires compensating winding.

Q: Multiple choices cont.: c. The 3M load contacts are welded shut. d. The normally open 3M contact…

A: Asked to give the cause because of which the problem occurs

Q: The overall efficiency

A:

Q: 6 What is the relay and what are its two circuits?

A: to know about the relay.

Q: With the aid of diagrams/illustrations describe the operation and applications of the following…

A:

Q: 8.a. What is the purpose of relay CRE in the roll stand machine? A. Relay CRE is used as an…

A: CRE relay is used to detect fault in the input circuit. It is used in stop button of contact welding…

Q: A three-phase motor can be made to run backwards by A. connecting a resistor in series with the…

A:

Q: Describe the function of relay. Sketch a circuit to explain the function of relay.

A: In electrical engineering there are certain devices and machine that are used to protect the main…

Q: If generator armature current is 2A, the motor armature current is 3A, Voltage is 240V,motor…

A: Generator current Ig = 2A Motor current Im = 3A Voltage V=240V Motor Armature resistance Ra= 4 ohm…

Q: A four poles d.c Motor with a progressive simplex wave winding, 14 slots , Draw developed diagram…

A: DC motor with a progressive simplex wave winding; pole=4 slot=14 Draw the developed diagram; a)The…

Q: What is the use of auxiliary contact in the magnetic controller?

A: The auxiliary contact is often used for the transmission circuit One contactor can have many…

Q: 10. Excitation losses in a transformer must be determined. When running the test, you should make…

A: Losses in Transformer  Ohmic loss  Excitation or Core loss Hysteresis loss Eddy current loss…

Q: For the Starting Up the Power Station Simulator Why are certain operations blocked by isolators

A:

Q: (B)-Draw a neat diagram to show potential divider arrangement of rheostatic control speed for d.c.…

A: Potential divider arrangement of rheostatic control speed for D.C. shunt motors: Rf Field…

Q: 2. Two similar coupled machines of same rating, each having an armature resistance of 0.5 Q are…

A:

Q: 21. A servo system is oscillating at standstill. This is an indication that A. a motor winding is…

A:

Q: A 3 kW, 315 V DC series motor is being supplied by a feeder with total resistance of 0.02 ohms and…

A: In this question,  We need to determine the armature voltage of the DC series motor.  If total…

Q: Explain the difference between load and auxiliary contacts.

A: Auxiliary contacts are small. These are used as part of control circuit .

Q: Why stationary armature type alternator is widely used ? Option 1: 2 slip rings used, more…

A: Why stationary armature type alternator is widely used ? Option 1: 2 slip rings used, more efficient…

Q: 6.a. Arcing in manual starters is eliminated by the use of A. overload relays. B. nonconductive…

A: Here we discuss about the MCQs on the motor protection.

Q: Calculate the field copper loss at no -load and rated voltage for CW rotation of the armature and…

A:

Q: Iwo Cempeundgenerator A and B fitted wi a total lo ad current of an equalizing bar supply a total…

A: In this Compound generator V= bus bar voltagev=voltage between equilazer bus-bar and the…

Q: (B)- Indicate whether the following statements are true or false and correct the false statements…

A: In this question we will write dc machine related questions.... Note :- as per our guideline , I am…

Q: 12.a. The easiest place to install an ammeter into a stepper motor driver/motor circuit for system…

A: Here we deal with the MCQs. as given related to the stepper motor.

Q: How does a clamper circuit perform clamping action?

A: SOLUTION  CLAMPER CIRCUIT A Clamper circuits generally consists of a…

Q: Determing the front pitch, back pitch, and average pitch of the armature winding.  12 poles     100…

A:

Q: explain in detail and type the solution

A: An Electric Drive is responsible for various controls of an electrical motor or generator. It…

Q: The preferred method for applying the field excitation voltage uses a field relay which operates on…

A: An excitation voltage or current is the amount of direct current (D.C.) electric energy that is…

Q: What is the speed of an inductor motor of 7 poles if the slip is 2.1%

A:

Q: * True or False False True Since insulation required is less, Star Connection can be .used for long…

A: Given five statement, and we need to identify whether the statement is true or false.

Speed control of motor

Speed control by DC motor-speed controller is required to realize variable speed drive. Whenever a motor drives a particular load, it is called drive, and variable speed drive refers to a load requiring variable speed. All this is obtained by a DC motor speed controller.