In the circuit shown in the figure th ammeters measurements .....are Rs 1500 R1 1500 sod R4 R2 sod E, - 20 V E2 -24 V

Q: What is the voltage drop across RC, VC, in volts?  (Enter the number, not the units.)

A: Given circuit is -

Q: difference between measurement uncertanty and measurement error

A: Given : Need to find the difference between measurement error and uncertainty.

Q: Is Mc microfarads?

A: Given, The abbreviation of mc =?

Q: Choose which answers are correct ‎‏What is the unit of slope of a Fuel cost curve ? a . $ / MWh b .…

A:

Q: Sl.no Symbols Name of the components 1. 2. 3. 4.

A: here, the various symbols of the pneumatic circuits are given  which can be useful to make PLC…

Q: Khee Voltage of Ilicon semi nductor. (without Your answer A condition where zero (0) volt is less…

A: 1) Knee voltage of silicon semiconductor is 0.7

Q: What is sub station

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: recall the topcis of the electronic Device and circuits

A: There are many topics in EDC  These topics are  1- Semiconductor diode  2-Diode circuit

Q: 1.verify (Kc) and (KUL)) ?

A:

Q: Q2. What are the major carriers in the depletion region? Explain.

A: Here i have described it.

Q: Given the information appearing in Figure beside (assume Ic=IE) determine: (a) Ic. (b) VE. 18 V (c)…

A: Disclaimer:  Since you have asked multipart questions, we will solve the first three subpart for…

Q: What is the acceptable minimum value of leakage current of HI-POT Test of electrical cables. Can you…

A: According to the question,what is the acceptable minimum value of leakage current of HI-POT Test of…

Q: +V1ev1- L3 13/23 R2 v5 es V4 e4 |12/02 Figure 2060

A:

Q: Q2: (A)Find the following: 1- (110)10+ (0111)2.by using BCD numbers. 3-(3E91)16- (1F93)16by using…

A: The number system is used to represent information in digital electronics. Different bases exist in…

Q: tronic components definitions and si units and color coding

A: Electronic components : There are mainly two type of Electronic components one is active Electronic…

Q: Label the parts of Tubular Steel Poles

A: Steel tabular poles are not commonly used poles these poles are used when there is need of low cost…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: Use electricity cost $0.08 to $0.30 in increments of $0.01. Compute a column for each type of bulb…

A:

Q: Identify each characteristic curve by the type of FET that it represents. Ip -VGS +VGs

A: For N channel JFET, the VGS voltage is negative and the saturation current IDs we obtain at Vgs.

Q: Identify the elements considered for the Voltage Drop calculations in D.C distribution system. O a.…

A: Inductive reactance (XL) = 2πfL  Shunt admittance (Yc)= 2πfC In dc distribution, the frequency of…

Q: Q1. Convert following numbers in given radix system: a. (173)10 into hexadecimal b. (2E3)16 into…

A:

Q: The neutral current is equal to three times of ....... sequence current.

A: Current in nautral is sum of three phase currents. Current in each phase is sum of possitive…

Q: From the table, what is the circular mils for the following: a. 14 AWG a. 10 AWG b. 30 AWG c. 20 AWG

A:

Q: 19. Identify the response time of a meter. a. Time taken by output to reach final constant value…

A: Identify the response time of a meter. It's depend on the parameter.

Q: In FET, An outward-pointing arrow represents ___. Choose the correct answer below: a.N-type…

A:

Q: Determine Reg in Ohms at the (a,b) terminals for the following circuit. Round your answer to the…

A:

Q: HERE IS IT

A: Physical address can be expressed by the following formula:Physical Address = (Segment Address) x 10…

Q: Use block diagram formula

A:

Q: Question : Explain the concepts of lattice matched hetero-structure. Don’t copy other works.…

A: It is asked to explain the concept of lattice matched hetero-structure.

Q: The circuit shown in Figure Q5.1 consists of a current source connected to a load via a cable. The…

A: Given circuit is - Value of current source is -

Q: Explain the Difference between the Fundamental and Derived Unit.

A: There are generally  three types of units which are used to typically measure a particular physical…

Q: What do you understand by Safety factor, puncture and Flashover of Insulator

A: The part section of a pin type insulator is shown in  the figure below:

Q: At pinch-off voltage, the drain current in a FET is ___. Choose the correct answer: a.zero…

A: At pinch-off voltage, the drain current in a FET is ___.   Choose the correct answer: a.zero…

Q: diff b/w aproximated & Interp0leted Curves. (Brief explanation with sketches)

A: Graphs are the pictorial representation of the system when we vary one quantity with respect to the…

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.