In the circuit shown in figure 3 (constructed of ideal elements), the inductor current at t=0 was 2.0 A. The switch was opened at t = 0 sec and the voltage across the capacitor, V, quickly reached a maximum (negative) value of -10 V. After an elapse of 250 sec, Ve dropped down to -5 V. Determine the value of L, the back resistance of the diode, and the time constant (t = RC ), of the capacitor discharge circuit. V S R = 1092 t=0 Y İL Figure 3 Diode C=10 μF

In the circuit shown in figure 3 (constructed of ideal elements), the inductor current at t=0 was 2.0 A. The switch was opened at t = 0 sec and the voltage across the capacitor, V, quickly reached a maximum (negative) value of -10 V. After an elapse of 250 sec, Ve dropped down to -5 V. Determine the value of L, the back resistance of the diode, and the time constant (t = RC ), of the capacitor discharge circuit. V S R = 1092 t=0 Y İL Figure 3 Diode C=10 μF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The current flowing in a PN junction diode at room temperature is 5mA. The leakage (reverse) current at 20°C temperature is 2µA and the ideality factor n is 1.77.Find bias voltage (q is the electronic charge (1.6×10-19 C), k is Boltzmann’s constant (1.38×10-23 J/K))
1-In the circuit designed to measure the effective value of the sinusoidal voltage at the input, diodes are considered ideal. M deflection is a measuring element with rotating coil. Rm=2k İm=(10)^-4 A. A- Draw the waveform of the current flowing through M on a scale. Determine the resistance value of R1 so that the nominal voltage value of V-m is 100V. B-What should the tolerances of the resistors be so that the Vm class is at most 1.5? (resistors have the same tolerances). R1 u(t) R2 1R3 18k 20k R4 k: k2 10k
Determine the forward voltage and forward current of a diode in a circuit. The circuit is composed of a dc voltage source with its positive terminal of 10V connected in series to a 1Kohms resistor and the anode of a diode. The cathode of the diode is connected to ground. Use ideal device model approach. Draw the circuit and show your solution/s.
In the given circuit, (diodes will be considered ideal.a) Draw the V0 output by calculating it according to the input.b) Calculate the average and effective value of the V0 output.c) What are the advantages and disadvantages of using two diodes and two resistors instead of four diodes?Input signal Vm = ± 10V (peak to peak), T = 2π (period), R = 32k
For a sinusoidal input of 40 V (p-p) to the given circuit, what is the minimum value of the output waveform? NOTE: use ideal diode * 0.7 30 O 20 O -5 O -40
Can you help me solve this and explain clearly I saw some answers on chegg but I don’t understand it .
Please answer in typing format solution Sir please help Thanks in advance
What is the dynamic resistance of a diode if its Ip = 4.06 mA? No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places.
⦁ Consider the below zener diode circuit and find the values of , , , . Use the constant voltage drop model which is shown is Figure 2. Show your solution steps clearly and explain them. The answers without solution steps will not be graded. Also, state your results in the sections below the circuits. ( = 0.1 )
Please show all work, thank you :)
I need a more detailed explanation of this. I'm new to electronics. I don't know what is the Diode Current.
?